Projecta INTELLI-CHARGE IC25 Скачать руководство пользователя страница 24

WARRANTY STATEMENT

Applicable only to product sold in Australia

Brown & Watson International Pty Ltd of 1500 Ferntree Gully Road, Knoxfield, Vic., 
telephone (03) 9730 6000, fax (03) 9730 6050, warrants that all products described in 
its current catalogue (save and except for all bulbs and lenses whether made of glass or 
some other substance) will under normal use and service be free of failures in material and 
workmanship for a period of one (1) year (unless this period has been extended as indicated 
elsewhere) from the date of the original purchase by the consumer as marked on the 
invoice. This warranty does not cover ordinary wear and tear, abuse, alteration of products 
or damage caused by the consumer. 
To make a warranty claim the consumer must deliver the product at their cost to the 
original place of purchase or to any other place which may be nominated by either BWI or 
the retailer from where the product was bought in order that a warranty assessment may 
be performed. The consumer must also deliver the original invoice evidencing the date and 
place of purchase together with an explanation in writing as to the nature of the claim.
In the event that the claim is determined to be for a minor failure of the product then 
BWI reserves the right to repair or replace it at its discretion. In the event that a major 
failure is determined the consumer will be entitled to a replacement or a refund as well as 
compensation for any other reasonably foreseeable loss or damage.
This warranty is in addition to any other rights or remedies that the consumer may have 
under State or Federal legislation.

IMPORTANT NOTE

Our goods come with guarantees that cannot be excluded under the Australian Consumer 
Law. You are entitled to a replacement or refund for a major failure and compensation for 
any other reasonably  foreseeable loss or damage. You are also entitled to have the goods 
repaired or replaced if the goods fail to be of acceptable quality and the failure does not 
amount to a major failure.

IS155

Issue 8 20.06.22

Distributed by

AUSTRALIA
Brown & Watson International Pty. Ltd.

Knoxfield Victoria 3180
Phone: (03) 9730 6000
Fax: (03) 9730 6050
National Toll Free: 1800 113 443

NEW ZEALAND OFFICE
Griffiths Equipment Ltd.

19 Bell Avenue, 
Mount Wellington, 
Auckland 1060, New Zealand
Phone: (09) 525 4575 
Fax: (09) 579 1192

Содержание INTELLI-CHARGE IC25

























Отзывы: