background image

12

WARRANTY STATEMENT

Applicable only to product sold in Australia

Brown & Watson International Pty Ltd of 1500 Ferntree Gully Road, Knoxfield, Vic., telephone 
(03) 9730 6000, fax (03) 9730 6050, warrants that all products described in its current catalogue 
(save and except for all bulbs and lenses whether made of glass or some other substance) will 
under normal use and service be free of failures in material and workmanship for a period of 
one (1) year (unless this period has been extended as indicated elsewhere) from the date of 
the original purchase by the consumer as marked on the invoice. This warranty does not cover 
ordinary wear and tear, abuse, alteration of products or damage caused by the consumer. 
To make a warranty claim the consumer must deliver the product at their cost to the original 
place of purchase or to any other place which may be nominated by either BWI or the retailer 
from where the product was bought in order that a warranty assessment may be performed. 
The consumer must also deliver the original invoice evidencing the date and place of purchase 
together with an explanation in writing as to the nature of the claim.
In the event that the claim is determined to be for a minor failure of the product then BWI 
reserves the right to repair or replace it at its discretion. In the event that a major failure is 
determined the consumer will be entitled to a replacement or a refund as well as compensation 
for any other reasonably foreseeable loss or damage.
This warranty is in addition to any other rights or remedies that the consumer may have under 
State or Federal legislation.

IMPORTANT NOTE

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.  
You are entitled to a replacement or refund for a major failure and compensation for any other 
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced  
if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Distributed by
AUSTRALIA

 

Brown & Watson International Pty Ltd

Knoxfield, Victoria 3180
Telephone  (03) 9730 6000
Facsimile 

(03) 9730 6050

National Toll Free 

1800 113 443

NEW ZEALAND
Narva New Zealand Ltd

22–24 Olive Road
PO Box 12556 Penrose
Auckland, New Zealand
Telephone 

(09) 525 4575

Facsimile  

(09) 579 1192

IS361

Issue 1 28.2.17

Содержание BLT700













Отзывы: