ProHD DT-X93H Скачать руководство пользователя страница 2

 

Preface 

1.  All internal technologies of this product are protected, including device, software and trademark. 

Reproduction in whole or in part without written permission is prohibited. 

2.  All brands and trademarks are protected and other relative trademarks in this user manual are the 

property of their respective owners. 

3.  Due  to  constant  effort  of  product  development,  SWIT  Electronics  reserves  the  right  to  make 

changes and improvements to the product described in this manual without prior notice. 

4.  The warranty period of this product is 2 years, and does not cover the following:   

(1) Physical damage to the surface of the products, including scratches, cracks or other damage to 

the LCD screen or other externally exposed parts; 

(2) The LCD dot defects are not over three;   
(3) Any damage caused by using third-party power adaptors; 
(4) Any damage or breakdown caused by use, maintenance or storage not according to the user 

manual. 

(5) The product is disassembled by anyone other than an authorized service center. 
(6) Any damage or breakdown not caused by the product design, workmanship, or manufacturing 

quality, etc. 

5.  For  any  suggestions  and  requirements  on  this  product,  please  contact  us  through  phone,  fax, 

Email, etc. 

 
 
 
 
 
 
 
 
 

SWIT Electronics Co., Ltd. / SWIT Electronics USA, LLC 

Address: 3350 Scott Blvd. 61-02, Santa Clara, CA 95054 
Toll free: 1 866 986-SWIT(7948) 
Tel: 408 260-8258 
Fax: 408 228-8438 
Email: [email protected] 
Website: 

www.swit.us

 

 

Содержание DT-X93H




















Отзывы: