
TDR-26
Operator’s Manual
11
•
Keep away from overhead electrical lines. Electrocution
can occur without direct contact
•
Clean reflectors, Slow Moving Vehicle sign and lights
before transporting. Use power unit hazard lights.
•
Before disconnecting from power unit, always place
controls in neutral, set park brake, turn engine off, and
wait for all moving parts to stop. Relieve hydraulic
pressure per power unit manufacturer’s instructions.
•
Ensure mower parking jack is securely fastened to
mower frame with supplied pin before removing hitch
draw pin.
MAINTENANCE SAFETY PRECAUTIONS
•
Never make adjustments or repairs with the engine running.
Always disengage PTO, engage parking brake, turn engine off,
lower wings to cutting position and relieve hydraulic pressure
before performing any maintenance.
•
Observe and perform proper lock-out procedures for power unit
if attached to mower during service.
•
Keep nuts and bolts tight and properly torqued, especially
blade attachment bolts. Check that all cotter pins are properly
installed. Keep equipment in good condition.
•
Keep mower free of grass, leaves, or other debris build-up.
•
Never work on raised mower decks without safety locks in
place.
•
Periodically check condition of safety devices, guards, and
deflectors. Replace only with manufacturer’s recommended
parts.
•
Inspect and replace damaged blades. Use only original OEM
parts. Blades can fail from poor maintenance practices.
•
Handle mower blades carefully. They are sharp and can cut
unprotected skin. Use caution and wear gloves when handling
them.
•
Check to make sure hydraulic hoses are not worn or damaged
and are routed to avoid chafing.
•
Immediately replace any hydraulic hose that shows signs of
swelling, wear, leaks or damage so it does not burst.
•
Do not use your hand to check for hydraulic oil leaks. Use a
piece of cardboard instead.
•
Hydraulic fluid escaping under pressure can penetrate the skin
causing serious injury. If skin penetration occurs, seek medical
attention
immediately.
Relieve
all
pressure
before
disconnecting hoses.
•
Do not bend or strike hydraulic lines, tubes or hoses, or
reinstall them in a bent or damaged condition.
Содержание TDR-26
