Progressive Turf Equipment SDR 65 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 48

background image

27

“V” BELT TENSION:

Proper belt tensioning is a fundamental factor in the successful V-belt

operation. Lack of tension will cause slippage, and too much tension will cause
excessive belt stretch as well as damage to the drive components, such as bearings
and shafts. Therefore, to ensure proper belt tension, the following procedure is
recommended.

CHECKING BELT TENSION

At the mid-point of the span, apply a deflection force with a spring scale in

the direction perpendicular to the span until the belt is deflected the 3/8”.

The recommended force to deflect the belt is a minimum of 4.9 lbs. to a maximum
of 7.3 lbs.

The first 24 to 48 hours of operation is the belt “run in” period. To ensure

satisfactory belt performance, belt tension should be checked during this time
period.

«
...
27
28
29
30
31
...
»

Содержание SDR 65

















































Отзывы:

Нет отзывов

Похожие инструкции для SDR 65

PERFECT ZW Series

Бренд: VAN WAMEL Страницы: 69

Бренд: Yazoo/Kees Страницы: 46

Бренд: Oleo-Mac Страницы: 292

Бренд: Toro Страницы: 12

Бренд: Sabo Страницы: 100

Бренд: Simplicity Страницы: 52

Бренд: Toro Страницы: 36

A12612A Stockman PRO

Бренд: COX Страницы: 48

Бренд: VonHaus Страницы: 12

Бренд: Eliet Страницы: 106

Бренд: Webb Страницы: 12

Бренд: Land Pride Страницы: 2

Бренд: Cub Cadet Страницы: 44

Бренд: Parkside Страницы: 60

Бренд: Homelite Страницы: 64

Бренд: Dolmar Страницы: 41

Бренд: Dolmar Страницы: 76

Бренд: GÜDE Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды