Progress Lighting AirPro P250072 Скачать руководство пользователя страница 16

13. Specifications 

FAN 

SIZE

SPEED

VOLTS

FAN POWER

CONSUMPTION

(WITHOUT LIGHTS)

WATTS

AIRFLOW

CFM

AIRFLOW 

EFFICIENCY

(HIGHER IS BETTER)

CFM/WATT

NET

WEIGHT

GROSS

WEIGHT

CUBE 

FEET

56”

Low

120

2.92

2095

717.47

18.41

Lbs

22.93

Lbs

2.25

High

30.89

4844

156.81

©2017 Progress Lighting, Inc.

701 Millennium Blvd.,

Greenville, SC 29607

All Rights Reserved

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits 

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate 

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. 

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio 

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one 

or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful 

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.      

Содержание AirPro P250072

















Отзывы: