Progress Lighting AirPro P250072 Скачать руководство пользователя страница 14

Remote Control

Figure 21

Figure 22

Warm weather -  (Forward) A  downward  air 

flow creates a cooling effect as shown in Figure 

21. This allows you to set your air conditioner 

on  a  higher  setting  without  affecting  your 

comfort.
Cool weather - (Reverse) An upward air flow 

moves warm air off the ceiling are as shown in 

Figure 22. This allows you to set your heating 

unit on a lower setting without affecting your 

comfort.

Figure 20

11.

Timer:

While the fan is on press 2h - turns on a 2 hour run timer.
While the fan is on press 4h - turns on a 4 hour run timer.

While the fan is on press 8h - turns on an 8 hour run 

timer.

Forward/Reverse:

Changes direction of ceiling fan.

Breeze:

Press and release this button to enable the Breeze 

function, this will change your fan speed randomly, 

simulating a relaxing breeze.

Fan speed:

LEDs on the fan speed button will illuminate to the 

corresponding speed.
Press and release 1: turns the fan speed to 1.

Press and release 2: turns the fan speed to 2.
Press and release 3: turns the fan speed to 3.

Press and release 4: turns the fan speed to 4.

Press and release 5: turns the fan speed to 5.
Press and release 6: turns the fan speed to 6.

Fan OFF

:

Turns fan Off

Light ON/OFF

Press and release the light button to turn the light on.

Press and release the light button to turn the light off.

Dimmer:

Press and hold up dimmer button to increase the light 

level
Press and hold the down dimmer button to decrease the 

light level.

Timer

Light on 

Increases the

light level

(Dimmer)

Forward/

Reverse

Comfort

Breeze

Fan speed

Decreases the

light level

(Dimmer)

Light off 

Fan off 

2h

4h

8h

R

3 4

2

5

1 6

OFF

Содержание AirPro P250072

















Отзывы: