ProForm 615 T Treadmill Скачать руководство пользователя

Страница: 17 / 32

HOW TO TURN ON THE POWER

IMPORTANT: If the treadmill has been exposed to

cold temperatures, allow it to warm to room tem-

perature before you turn on the power. If you do

not do this, you may damage the console displays

or other electrical components.

Plug in the power cord (see

page 15). Next, locate the

power switch on the tread-

mill frame near the power

cord. Press the power switch

into the reset position.

IMPORTANT: The console features a display demo

mode, designed to be used if the treadmill is dis-

played in a store. If the displays light as soon as

you plug in the power cord and press the power

switch into the reset position, the demo mode is

turned on. To turn off the demo mode, hold down

the Stop button for a few seconds. If the displays

remain lit, see THE INFORMATION MODE on page

21 to turn off the demo mode.

Next, stand on the

foot rails of the

treadmill. Find the

clip attached to the

key and slide the

clip onto the waist-

band of your clothes.

Then, insert the key

into the console.

After a moment, the

displays will light. IMPORTANT: In an emergency,

the key can be pulled from the console, causing

the walking belt to slow to a stop. Test the clip by

carefully taking a few steps backward; if the key is

not pulled from the console, adjust the position of

the clip.

HOW TO USE THE MANUAL MODE

1. Insert the key into the console.

See HOW TO TURN ON THE POWER at the left.

2. Select the manual mode.

Press the Manual button on the console. If you

are not connected to iFit, the manual mode will be

selected automatically.

3. Start the walking belt.

To start the walking belt, press the Start button, the

Speed increase button, or one of the Speed but-

tons numbered 1 through 10.

If you press the Start button or the Speed increase

button, the walking belt will begin to move at 1

mph. As you exercise, change the speed of the

walking belt as desired by pressing the Speed

increase and decrease buttons. Each time you

press one of the buttons, the speed setting will

change by 0.1 mph; if you hold down the button,

the speed setting will change in increments of 0.5

mph. Note: After you press the button, it may take

a moment for the walking belt to reach the selected

speed setting.

If you press one of the numbered Speed buttons,

the walking belt will gradually change speed until

it reaches the selected speed setting. To select a

speed setting that includes a decimal—such as 3.5

mph—press two numbered buttons in succession.

For example, to select a speed setting of 3.5 mph,

press the 3 button and then immediately press the

5 button. Note: This will not function if the console

is set to metric units.

To stop the walking belt, press the Stop button.

The time will begin to flash in the display. To restart

the walking belt, press the Start button or the

Speed increase button.

4. Change the incline of the treadmill as desired.

To change the incline of the treadmill, press the

Incline increase or decrease button or one of the

Incline buttons numbered 1 through 10. Each time

you press one of the buttons, the treadmill will

gradually adjust to the selected incline setting.

Reset

ETPF59511

(PFTL59511)

Key

Clip

Содержание 615 T Treadmill

































Результаты поиска

Содержание 615 T Treadmill

Отзывы:

Похожие инструкции для 615 T Treadmill

Бренды по названию

Популярные бренды

ProForm 615 T Treadmill, Руководство пользователя

Результаты поиска

Содержание 615 T Treadmill

Отзывы:

Похожие инструкции для 615 T Treadmill

Бренды по названию

Популярные бренды