Profibus T1H-PBC Скачать руководство пользователя страница 6

Страница: 6 / 7

Expansion I/O Configurations

T1K-10CBL

T1K-10CBL-1*

Right side to left side

expansion cable

Using T1K-10CBL expansion cable

and T1K-05CBL-RR expansion cable

Expansion cables

T1K-05CBL-LL

T1K-05CBL-LL-1*

Left side to left side

expansion cable

Using two T1K-10CBL expansion cables

Using T1K-05CBL-RR expansion cable

and T1K-05CBL-LL expansion cable

Using T1K-05CBL-RR expansion cable

The T1K-10CBL(-1) connects the right
side of an I/O base to the left side of
the next I/O base. A maximum of two
T1K-10CBL(-1) cables can be used per
expansion system.

The T1K-05CBL-LL(-1) connects the left
side of an I/O base to the left side of the
next I/O base. Only one T1K-05CBL-LL
(-1) cable can be used per expan-
sion system and must be used with a
T1K-05CBL-RR cable

This cable cannot

be connected to the left side of the network

interface base.

Some of the examples below show
the T1K-05CBL-RR expansion
cable. This cable is no longer
available.

Refer to the examples if you already
have these cables. If you are
purchasing new cables, we recom-
mend the T1K-10CBL(-1) cables.
The T1K-05CBL-RR connects the
right side of an I/O base to the right
side of the next I/O base. A maximum
of one T1K-05CBL-RR cable can be
used per expansion system.

Note:

When this cable is used, the expan-

sion I/O assignments are from right

to left (reversed).

*Note:

The (-1) versions of the expansion cables pass 24VDC through on an isolated wire. (All cables pass the 5VDC base

power.) Any local expansion DC input module configured for “internal power” (current sourcing) must either have a power supply
preceding it on the same base or, have a (-1) version cable pass 24VDC from a power supply on the preceeding base.

T1K-10CBL

T1K-05CBL-RR
(Retired Product)

T1K-05CBL-LL

In the system below, power supplies can be used anywhere.

Power supplies can be used anywhere in the first two bases,
but not in the last expansion base.

A power supply can be
used on either base.

Power supplies can be used anywhere in the first and third
bases, but not in the second base.

T1K-10CBL(-1)

Power supplies can be used anywhere in the first base, but not
in the second base.

I/O Addressing

T1K-10CBL(-1)

Do not connect a

T 1 K - 0 5 C B L - L L ( - 1 )
to the left side of the
network interface base.

Cable length = 1.0m

Cable length = 0.5m

T1K-05CBL-RR RETIRED
Right side to right side

expansion cable is no longer

available

w w w . l a m o n d e . c o m - f i e l d I O

Universal Field I/O

tFED-56

Содержание T1H-PBC








Результаты поиска

Содержание T1H-PBC

Отзывы:

Бренды по названию

Популярные бренды

Profibus T1H-PBC, Руководство пользователя

Результаты поиска

Содержание T1H-PBC

Отзывы:

Бренды по названию

Популярные бренды