Profi Cook PC-SM 1237 A, Инструкция по эксплуатации

Страница: 10 / 54

PC-SM1237A_IM 12.10.22
10
Do not use power supply with damaged plug! If
the pins of the plug part are damaged, the plug-in
power supply shall be scrapped.
CAUTION:
• Choose a charging location that does not expose the
appliance to direct sunlight or other heat sources.
• Do not charge the battery unattended.
• After charging, always disconnect the charging cable
from the appliance and the power supply unit from the
socket.
WARNING:
If you use the appliance in hot food, there is a risk of
burns from hot splashes.
• Immerse the blender rod in the food before switching
on the appliance. This will prevent splashing.
CAUTION:
Do not use this appliance to chop hard foods such as ice
cubes, nutmeg or large pieces of block chocolate. This
may destroy the blades!
• Chop large pieces of solid food before puréeing (max.
Ø 1.5 cm) and add some liquid.
• Short-time operation: Do not use the appliance con -
tinuously for more than 1 minute. Let the appliance cool
down for about 1 minute before using it again.
• If the food is too solid, stop the process after 10 seconds.
Reduce the amount of food being mixed. Loosen up solid
food. This will prevent the motor from overheating.
Meanings of the LED Status Indicators (3)
LED flashes red During charging
LED lights up blue continuously After charging
LED lights up blue for 7 seconds after
pressing the safety switch twice
Standby status
LED flashes red for 7 seconds after
pressing the safety switch twice
False start
Charging the Built-in Battery
Check the charge status of the rechargeable battery: Press
the safety switch (2) twice quickly. If only one blue LED
lights up on the battery status indicator (6), the battery must
be charged. Two illuminated LEDs indicate that the capacity
of the battery is between 33 % and 66 %.
It is not possible to operate the appliance during the charg
-
ing process.
To charge the battery, proceed as follows:
1. Connect the charging cable to the USB-C port on the
back of the appliance and the power supply unit.
2. Connect the power supply unit to an approved power
outlet.
- The LED (3) under the safety switch indicates the
charging status.
- The LED (3) goes out when you disconnect the mains
plug from the socket.
- It is normal for the appliance to heat up during
charging.
3. Stop charging after 2.5 hours at the latest or when the
LED (3) lights up blue continuously.
CAUTION:
After charging, always disconnect the charging cable
from the appliance and the power supply unit from the
socket.
Assembly / Disassembly
WARNING: Risk of Injury!
• During assembly, there is a risk of crushing your
fingers. Be especially careful.
• Check that the appliance is not in standby status to
avoid unintentional switch-on and thus a hazard.
Attach the Blender Rod
Place the blender rod on the motor housing until it clicks
into place.
Remove the Blender Rod
When dismantling, pull the blender rod off the motor hous -
ing while holding down the two buttons (9).
Protection Against Unintentional Switch-on
The appliance has a safety switch (2). You can only use the
appliance if you press this safety switch twice quickly. The
LED (3) indicates readiness for operation for 7 seconds. If
the LED goes out, further operation is blocked.
Operation
1. Immerse the entire blender head in the foodstuff or
beverage. Hold the appliance vertically. This way you
avoid splashes.
2. Press the safety switch (2) twice quickly.
3. Grasp the handle with one hand so that you can press
the push button (4). Start within 7 seconds.
When the LED (3) goes out, the appliance is no longer
ready for operation. The process must be started again.
4. With the other hand, you can adjust the speed with the
or buttons. The green LED shows you the speed
level.
- You achieve a pulse mode by pressing and releasing
the push button in intervals.
5. Release the push button before pulling the blender head
out of the food.