CIRCULAR TRIMING:
1. The adjusting conductor (28, 29, 31-37) is used when triming curved edges.
2. Slide adjusting conductor onto holder with both grooves properly lined up.
3. Make sure to keep sufficient distance between tube (29) and cutting bit. Tube should
be somehwhat underneath bit.
4. The adjust screw (33) is used to control the amount of stock removed from the edge.
Screw (32) must be tighten securely.
5. Each complete rotation of the knob adjusts the amount removed by 3/64”, Clockwise
rotation causes more stock to be removed and counter-clockwise causes less stock
to be removed.
6. Keep tube firmly against edge of stock during operation.
5. Adjust for desired radius, then tighten down butterfly nut.
6. Drive small nail or similar fastener through the remaining hole.
7. Cut circle in a clockwise direction.
MAINTENANCE
1.
BEFORE EACH USE,
inspect the general condition of the tool. Check for:
• Loose hardware,
• Misalignment or binding of moving parts,
• Damaged cord/electrical wiring,
• Cracked or broken parts, and
• Any other condition that may affect its safe operation.
2.
AFTER USE,
wipe external surfaces of the tool with clean cloth
3. Periodically, wear ANSI-approved safety goggles and NIOSH-approved breathing
protection and blow dust out of the motor vents using dry compressed air.
4. Periodically wipe the Collet, Collet Cone, and router bits with a light oil to prevent rust.
5. Over time, if the performance of the tool diminishes, or it stops working completely,
it may be necessary to replace the Carbon Brushes.
This procedure must be completed by a qualified technician.
6.
WARNING!
If the supply cord of this power tool is damaged, it must be replaced
only by a qualified service technician.
TROUBLESHOOTING
Problem
Possible Causes
Likely Solutions
Tool will not start.
1. Cord not connected.
2. No power at outlet.
3. Tool’s thermal reset breaker
tripped (if equipped).
4. Internal damage or wear.
(Carbon brushes or Power
Switch for example.)
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.
3. Turn off tool and allow to cool.
Press reset button on tool.
4. Have technician service tool.
Tool operates slowly. 1. Forcing tool to work too fast.
2. Extension cord too long or cord
diameter too small.
1. Allow tool to work at its own rate.
2. Eliminate use of extension cord. If an extension
cord is needed, use one with the proper diameter
for its length and load. See
Extension Cords
in
Grounding
section on page 2.
Performance
decreases over time.
1. Carbon brushes worn
or damaged.
2. Router bit dull or damaged.
1. Have qualified technician replace brushes.
2. Use sharp bits. Replace as needed.
Excessive noise
or rattling.
Internal damage or wear. (Carbon
brushes or bearings, for example.)
Have technician service tool.
Overheating.
1. Forcing tool to work too fast.
2. Accessory misaligned.
3. Router bit dull or damaged.
4. Blocked motor housing vents.
5. Motor being strained by long or
small diameter extension cord.
1. Allow tool to work at its own rate.
2. Check and correct accessory to
fence and/or table alignment.
3. Use sharp bits. Replace as needed.
4. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed air.
5. Eliminate use of extension cord. If an extension
cord is needed, use one with the proper diameter
for its length and load. See
Extension Cords
in
Grounding
section on page 2.
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
5
1-800-348-5004
6
1-800-348-5004
