background image

19

COMBUSTION AIR INDUCER

Under normal operating conditions, the combustion air inducer should be checked and cleaned prior to the heating season 

with the power supply disconnected. Use a small brush to clean inducer wheel.

ELECTRICAL

1. Check all wiring for loose connections.

2. Check for correct voltage at unit (unit operating).

3. Check amperage draw.

FLUE AND CHIMNEY

Check all vent and vent connector joints for tightness. Ensure that connections are sealed and that there are no blockages.

FAILURE TO OPERATE

If unit fails to operate check the following:

1. Is thermostat calling for heat?

2. Is main disconnect closed?

3. Is there a breaker tripped or a fuse blown?

4. Is gas turned on at meter?

5. Is manual shutoff valve open?

6. Is unit ignition system in lock out? If unit locks out again, call service technician to inspect unit.

7. Is pressure switch closed? Obstructed flue will cause unit to shut off at pressure switch. Check flue passage and outlet.

SAFETY SHUT−OFF VALVE TEST

The safety shut−off valve test procedure is as follows:

1. Turn off the manual gas valve.

2. Set the thermostat to call for heat.

3. System begins normal sequence of operation.

4. After approximately 30 seconds (pre purge period) the LED will fast flash indicating the gas valve is powered.

5. After 10 seconds, the gas valve closes and steps 4 and 5 will repeat two additional times before locking flashes on  

  the LED.

6. To restart the system, de−energize the thermostat call for heat and follow the operating instructions under Unit Start−Up  

  and Operation.

NOTE

: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty.

PARTS UNDER WARRANTY

 

Call Customer Service toll free at (877)886-5989

 

for referral information. 

When calling Customer Service, have ready:

• 

Your name

• 

Your address

• 

Model and serial number of your heater

• 

How heater was malfunctioning

• 

Type of gas used (Propane/LP or Natural gas/NG)

• 

Purchase date

• 

Usually, we will ask you to return the defective part to the factory

PARTS NOT UNDER WARRANTY

 

Call Customer Service toll free at (877)886-5989 for referral information.

When calling Customer Service have ready:

• 

Model number of your heater

• 

The replacement part number

REPLACEMENT PARTS

Содержание GHBVL50























Отзывы: