Prochem LEGEND GT Скачать руководство пользователя страница 49

Страница: 49 / 137

Maintenance

PROBLEM

CAUSE

SOLUTION

Loss of vacuum

While cleaning, the
vacuum is not up to
specification. Engine
RPM is normal.

Vacuum gauge is giving an improper
reading.

Examine the tubing between the vacuum
relief valve and the vacuum gauge and
remove any blockage.

Vacuum hose(s) is damaged, causing a
suction leak.

Inspect hose(s), repair or replace.

Waste tank gaskets not sealing properly, not
positioned properly

Inspect the gaskets. Repair or replace
gaskets as necessary. Re-position lid, inlet
and outlet.

Plugged vacuum hose or vacuum plumbing
between vacuum inlet and strainer basket.

Unplug vacuum hose or inlet plumbing.

Waste tank filter or strainer basket is
plugged.

Clean or replace filter. Clean strainer basket.

Loose vacuum pump drive belts.

Tighten the drive belts

Waste tank drain valve is damaged or left
open, causing a vacuum leak.

Close drain valve, if open. Remove the drain
valve and, after inspecting, replace the
defective components.

Vacuum relief valve requires adjustment or
has a vacuum leak due to damaged
diaphragm.

Re-adjust the vacuum relief valve. If the
vacuum does not increase, remove and
inspect the relief valve diaphragm. If
damaged, replace

Vacuum exhaust heat exchangers are
plugged with lint.

Remove and clean.

Vacuum pump is worn out.

Replace the vacuum pump.

Excessive Vacuum

Improper throttle adjustment.

Adjust throttle to set desired vacuum
pressure.

Vacuum obstruction

Inspect hoses for obstructions.

Vacuum relief valve requires adjustment.

Readjust the vacuum relief valve.

Loss of chemical

With the cleaning tool
valve open, no
chemical

Chemical pump is improperly primed.

Refer to chemical pump priming instructions.

The strainer at the inlet end of the chemical
inlet tube is clogged

Unclog the strainer. If damaged, replace.

Suction leak in the inlet tube leading into the
chemical pump.

Inspect inlet tube and flow meter for air leaks
or damage and replace, if required.

Chemical pump check valve(s) is clogged

Remove any debris from the chemical check
valve(s). Replace chemical check valve(s) or
seals, if necessary.

Chemical prime/on-off valve or chemical
metering valve is defective.

Replace valve(s).

Chemical pump diaphragm is ruptured.

Disassemble the chemical pump and replace
the damaged diaphragm and plastic disk.

Defective cylinder in the solution pump.

Measure the pump volume. If the pump
volume is less than normal, refer to “Loss of
Pump Volume” in the Troubleshooting section
in this manual.

86313050 LEGEND GT

Содержание LEGEND GT










































































































































Результаты поиска

Содержание LEGEND GT

Отзывы:

Похожие инструкции для LEGEND GT

Бренды по названию

Популярные бренды

Prochem LEGEND GT, Руководство по эксплуатации

Результаты поиска

Содержание LEGEND GT

Отзывы:

Похожие инструкции для LEGEND GT

Бренды по названию

Популярные бренды