3
EN
1-METER READY-TO-RUN SAILBOAT
Recommended Tools and Materials
• Paper towel
• Clear tape (DYNM0102)
• Pro Boat® Marine Grease and Gun (PRB0100)
• Medium or Thin CA (cyanoacrylate adhesive) or epoxy adhesive
• 2.5mm ball type hex wrench
• 7mm nut driver
• Small flat blade screw driver
• Small Phillips screw driver
• Small needle nose pliers
Table of Contents
Water-Resistant Boat with Waterproof Electronics ............................. 2
General Precautions ........................................................................... 2
Wet Conditions Maintenance ............................................................ 3
Recommended Tools and Materials ...................................................... 3
Product Inspection ................................................................................. 3
Specifications......................................................................................... 3
Transmitter Controls............................................................................... 4
Transmitter Battery Installation ............................................................ 4
Binding ................................................................................................... 4
Failsafe ................................................................................................... 5
Boat Assembly ....................................................................................... 5
Mast and Sail Assembly ........................................................................ 6
Lines and Winch Operation ................................................................... 7
Boating Tips ........................................................................................... 7
Getting Started ...................................................................................... 8
Control Direction Test ............................................................................ 8
Adjusting Sails ....................................................................................... 9
Trimming ................................................................................................. 9
Control Centering ................................................................................ 9
Centering Controls after Voyages ...................................................... 9
When You Are Finished ......................................................................... 9
Maintenance and Repair ..................................................................... 10
Troubleshooting Guide ......................................................................... 10
Limited Warranty ................................................................................. 11
Warranty and Service Contact Information ......................................... 12
FCC Information ................................................................................... 12
IC Information ...................................................................................... 12
Compliance Information for the European Union ................................ 13
Instructions for Disposal of WEEE ................................................... 13
Replacement Parts ............................................................................... 47
Optional Parts ...................................................................................... 47
Specifications
Length
39 in (1.0 m)
Front Beam (width)
14 in (360mm)
Back Beam (width)
14 in (355mm)
Mast Height
61 in (1.55 m)
Total Height
90 in (2.3 m)
Transmitter
2.4GHz 2-stick
Batteries
4 AA batteries (included) to
operate the transmitter.
4 AA batteries (included) to
operate the receiver.
Receiver
2.4GHz
Hull Material
Fiberglass
Sail Material
Rip-stop nylon
Sail Area (Main)
279 in
2
(0.18 m
2
)
Sail Area (Jib)
372 in
2
(0.24 m
2
)
Sail Area (Overall)
651 in
2
(0.42 m
2
)
Product Inspection
Carefully remove the boat and radio transmitter from the box. Inspect
the boat for damage. If your product is damaged, please contact the
hobby shop where you purchased your boat.
Wet Conditions Maintenance
• Drain any water that has collected in the hull by removing the
drain plug or canopy and tilting the boat in the appropriate
direction to drain the water.
CAUTION:
Always keep hands, fingers, tools and any loose or
hanging objects away from rotating parts.
• Remove the battery pack(s) and disconnect the ESC and motor.
Dry the contacts. If you have an air compressor or a can of
compressed air, blow out any water that may be inside the
recessed connector housings.
NOTICE:
Never use a pressure washer to clean your boat.
• Use an air compressor or a can of compressed air to dry the
boat and help remove any water that may have gotten into small
crevices or corners.
• Spray the bearings, fasteners and other metal parts with a water-
displacing light oil or lubricant. Do not spray the motor.
• Let the boat air dry before you store it. Water (and oil) may
continue to drip for a few hours.
Register your boat online at www.proboatmodels.com.
2.4 GHz
BATTERY
POWER
ON
OFF
N
N
R
R
CH2 REV.
CH1 REV.
