Recoil
®
17
Binding
Binding is the process of programming the receiver to
recognize the GUID (Globally Unique Identifier) code of a
single specific transmitter.
The STX2™ transmitter and
SPMSRX200 receiver are bound at the factory.
If you
need to rebind, follow the instructions below:
1.
Insert the Bind Plug in the BIND port of the ESC.
2.
Connect a fully charged battery to the ESC.
3.
Power on the ESC. The red receiver LED flashes,
indicating the receiver is in bind mode.
4.
Center the ST TRIM and TH TRIM dials on the
transmitter.
5.
Turn the Steering Wheel to Full Right. Power ON the
transmitter while holding the Steering Wheel
to the Right.
6.
Release the Steering Wheel when the receiver LED
goes solid.
7.
Remove the Bind Plug and store it in a convenient
place.
8.
Power OFF the ESC to save the settings.
9.
Power OFF the transmitter.
You must rebind when:
• When you want different failsafe positions
(e.g. when throttle or steering reverse has
been changed).
• Binding the receiver to a different transmitte
r.
NOTICE:
Do not attempt to bind the transmitter and
receiver if there are other compatible transmitters in
bind mode within 400 feet. Doing so may result in
unexpected binding.
1.
Pull and hold the Throttle Trigger to full throttle and
turn the ESC on.
2.
After 2 seconds a
“-B-B”
will sound. Wait another 5
seconds and the ESC will give a rising tone to indicate
you have entered
Programming Mode
.
3.
After entering Programming Mode, you will hear 4
tones in a loop indicating
Programmable Items
. Push
the Throttle Trigger to full brake within 3 seconds
after the tone sounds matching the programmable
item you want to select.
4.
After selecting a programmable item, you will hear
several tones in a loop indicating
Programmable
Values
. Pull Throttle Trigger to full throttle to select
the value matching the tone. The ESC will give an
alternating tone to indicate the item is selected.
5.
Keep the trigger in Full Throttle to return to
Step 3
and continue item selection. Move the throttle stick
to full brake position within 2 seconds to exit the
Program Mode.
The black-shaded setting is the factory default
Programmable Items
Programmable Value
-B
Single Beep
B––
Long Beep
-B
-B-B
-B-B-B
-B-B-B-B
B––
B––
-B
B––
-B-B
B––
-B-B-B
Running Mode
-B
Forward
Only
Forward/
Backward
Li-Po Cells
-B-B
Auto
Calc.
2s
3s
4s
5s
6s
Low Voltage Cutoff
-B-B-B
None
2.8V/Cell
3.0V/Cell
3.2V/Cell
3.4V/Cell
Timing
-B-B-B-B
0.00º
3.75º
7.50º
11.25º
15.00º
18.75º
22.50º
26.25º
ESC Programing
1.
Power on the transmitter and set the throttle TRIM
dial to the center position.
2.
Install the batteries in the boat and connect the
batteries to the ESC.
3.
With the ESC powered off, pull the throttle trigger to
full throttle and press the power buttons on both ESC
simultaneously. The ESC will beep twice. The green
light will flash with each beep.
4.
Return the throttle to neutral. The ESC will beep once
and the green light will flash once.
The calibration process is now complete. The ESC will arm
with beeps and flashes to announce the number of battery
cells it has detected. Reverse calibration is unnecessary.
Throttle Range Calibration
11
EN
