12
5
ASSEMBLY
Assembly requires two persons. Place all parts of the elliptical crosstrainer in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
In addition to the
included hex keys, assembly requires a phillips screwdriver , an adjustable
spanner , and a rubber mallet .
Use the chart below to identify the small parts used in assembly. The number in parentheses below each part is
the key number of the part, from the PART LIST on page 14. The number after the parentheses is the quantity
needed for assembly.
Note: Some parts may have been preattached for shipping. If a part is not in the
parts bag, check to see if it has been preattached.
M8
Washer (48)–4
M8 Split
Washer (59)–4
M8 Nylon
Locknut (38)–8
M10
Washer (35)–2
Pedal Arm Bolt Set (40)–2
M10 x 25mm
Patch Screw (22)–2
M6 x 48mm Flat Head
Screw (36)–4
M8 x 38mm Button Bolt (50)–4
M8 x 19mm Button
Screw (68)–4
M8 x 53mm Button Bolt (34)–4
Wave Washer
(9)–2
M4 x 20mm
Screw (43)–4
1. Identify the Front Stabiliser (10), which is narrower than
the Rear Stabiliser (not shown). Whilst another person
lifts the front of the Frame (1), attach the Front
Stabiliser to the Frame with two M8 x 53mm Button
Bolts (34), two M8 Washers (48), and two M8 Nylon
Locknuts (38).
10
38
34
1
48
48
1
Inspect and tighten all parts of the elliptical crosstrainer
regularly. Replace any worn parts immediately.
To clean the elliptical crosstrainer, use a damp cloth
and a small amount of mild soap.
Important: Keep
liquids away from the console, place only a sealed
water bottle in the water bottle holder, and keep
the console out of direct sunlight. During storage,
remove the batteries from the console.
BATTERY REPLACEMENT
If the console display becomes dim, the batteries
should be replaced; most console problems are the
result of low batteries. To replace the batteries, see
assembly step 3 on page 6.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, you must remove the Left Pedal Arm (11) and
the Left Side Shield (3).
Remove the Pedal Arm Bolt Set (40), the M10 x
25mm Patch Screw (22), the M10 Washer (35) and
the Wave Washer (9) from the Left Pedal Arm (11).
Remove the Left Pedal Arm. Next, remove the two M4
x 25mm Screws (56) and the four M4 x 16mm Screws
(42) from the Left Side Shield (3).
See the drawing below and locate the Reed Switch
(53). Loosen, but do not remove, the indicated M4 x
16mm Screw (42). Slide the Reed Switch slightly
toward or away from the Magnet (58) on the flywheel.
Retighten the Screw. Turn the left Pedal Disc (15) for a
moment. Repeat until the console displays correct
feedback. When the Reed Switch is correctly adjusted,
reattach the Left Side Shield (3) and the Left Pedal
Arm (11).
HOW TO ADJUST THE DRIVE BELT
If the pedals slip whilst you are pedaling, even when
the resistance is adjusted to the highest setting, the
Drive Belt (19) may need to be adjusted. To adjust the
Drive Belt, you must first remove the left side shield.
See HOW TO ADJUST THE REED SWITCH at the
left and remove the left side shield.
Next, loosen the
M8 x 22mm Flat
Head Screw
(41) and turn
the M10 x
60mm Button
Bolt (62) until
the Drive Belt
(19) is tight.
When the Drive
Belt is tight,
retighten the
Flat Head
Screw. Reattach the left side shield.
MAINTENANCE AND TROUBLESHOOTING
42
56
42
42
22
35
3
40
15
41
62
19
9
11
58
53
42
