5
12
Inspect and properly tighten all parts of the elliptical
trainer regularly. Replace any worn parts immediately.
The elliptical trainer can be cleaned with a soft cloth
and a small amount of mild detergent.
Do not use
abrasives or solvents. To prevent damage to the
console, keep liquids away from the console and keep
the console out of direct sunlight.
When storing the elliptical trainer, remove the batter-
ies from the console. Keep the elliptical trainer in a
clean, dry location, away from moisture and dust.
CONSOLE TROUBLESHOOTING
If the console does not function properly, replace the
batteries (see assembly step 3 on page 5).
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, first see assembly step 9 on page 7 and
remove the Pedals (13, 14). Next, see step 8 on page
7 and remove the Pedal Arms (11, 12).
Next, remove all Screws (51, 72) from the right Pedal
Disc (15), and slide the Pedal Disc off. Remove all
Screws (71, 64) from the Right Side Shield (4), and
remove the Right Side Shield. Remove all Screws
(52) from the Left Side Shield (3) and remove the Left
Side Shield.
Next, locate
the Reed
Switch (53).
Loosen, but
do not
remove, the
indicated
Screw (52).
Slide the
Reed Switch
slightly toward
or away from
the Magnet (58) on the flywheel. Retighten the Screw.
Turn the left Pedal Disc (15) for a moment. Repeat
until the console displays correct feedback.
When the Reed Switch (53) is correctly adjusted, reat-
tach the Side Shields (3, 4), the right Pedal Disc (15),
the Pedal Arms (11, 12), and the Pedals (13, 14).
HOW TO ADJUST THE DRIVE BELT
If you can feel
the pedals slip
whilst you are
pedaling, even
when the resis-
tance is set at
the maximum
level, the Drive
Belt (19) may
need to be
adjusted. To
adjust the
Drive Belt, you
must remove both side shields. See the instructions at
the left and remove the side shields.
Next, loosen the M8 x 22mm Flat Head Bolt (26) and
turn the M10 x 60mm Screw (62) until the Drive Belt
(19) is tight. Once the Drive Belt is tight, tighten the
Flat Head Screw. Reattach the side shields.
MAINTENANCE AND TROUBLESHOOTING
64
71
51
51
72
71
52
52
64
64
14
12
4
58
53
52
15
15
3
26
62
19
64
2. Whilst another person lifts the back of the Frame (1)
slightly, attach the Rear Stabiliser (9) to the Frame
with two M10 x 75mm Carriage Bolts (34) and two
M10 Nylon Locknuts (33).
33
1
2
34
9
33
1. Identify the Front Stabiliser (10). Whilst another per-
son lifts the front of the Frame (1), attach the Front
Stabiliser to the Frame with two M10 x 75mm
Carriage Bolts (34) and two M10 Nylon Locknuts
(33).
Make sure that the Front Stabiliser is turned
so the Wheels (22) are not touching the floor.
1
1
10
22
22
33
34
3. The Console (23) requires four “D” batteries (not
included); alkaline batteries are recommended.
Remove the screw from the battery drawer. Pull the
battery drawer open and insert four batteries.
Make
sure that the batteries are oriented as shown by
the markings inside the battery drawer. Close the
battery drawer and reattach the screw. Note: When
the batteries are installed correctly, the fan will turn on
for a moment.
3
23
Battery
Drawer
Batteries
4. Hold the Console (23) near the Upright (2). Connect
the console wire to the Upper Wire (44). Insert the
excess wire into the Upright.
Attach the Console (23) to the Upright (2) with four
M4 x 16mm Screws (52).
Be careful to avoid
pinching the wires.
Attach the Water Bottle Holder (63) to the Upright (2)
with two M4 x 22mm Screws (42).
4
2
Console Wire
52
42
23
44
Screw
63
