background image

7

3

 Dimensions

The GLC150-BG41-RSFL-24V unit dimensions are as follows.

ALARM

This relay switch remains OFF until the LT unit’s system software
completes its startup routine. During this startup period, this external
circuit must be informed that the LT is not yet operational.
Be sure to design a hold timer circuit that will start operations after
the startup routine is completed, or create an alarm monitoring sys-
tem that will monitor the LT unit’s circuits.

Contact Rating

0.15A, AC125V (Resistance Load)
0.6A, DC24V (Resistance Load)

Operating Time (Set Time at 20

o

C) 4ms or less

Recover Time (Reset Time at 20

o

C) 4ms or less

Minimum switching load

1mA / DC5V

Initial Contact Resistance

100m

 or less

2

 General Specifications

Rated Voltage

DC24V

Voltage Supply Range

DC20.4 to DC28

8V

Ambient Operating Temperature

0

 to 50

Ambient Humidity

20

RH to 85

RH (no condensation)

Atmospheric Pressure

800hPa to 1114hPa (2000 meter or lower)

Atmosphere

Pollution Degree 2

75.8 [2.98]

6 [0.24]

141.2 [5.56]

207 [8.15]

157 [6.18]

191.2 [7.53]

(Unit:mm [in.] : excluding projections)

Содержание LogiTouch GLC150-BG41-RSFL-24V













Отзывы: