background image

16

   E

ngl

is

h

Connection

Switch

Emergency Stop Switch / Stop Switch

With this product incorporating an emergency stop switch or a stop switch, the 
switch activates the contact output, when the switch is enabled. To reset the 
stop status (lock status), pull the button forward, or turn the button in the 
direction indicated by the arrow.
When the switch is pressed, ON/OFF status are as follows:

NOTE: 

When using a model without an emergency stop switch or without a stop switch, 

disconnect (NC) these signal lines.

3-Position Enable Switch

The 3-position enable switch has three positions: 1) Not pressed (released 
position), 2) Pressed to the intermediate position, 3) Pressed to the innermost 
position (fully closed).
When the switch is set at each position, ON/OFF status are as follows:

NOTE: 

The contact is OFF when the switch is pressed to the innermost position then 

returned to the not pressed position.

Key Switch

Turning the key turns this product’s power supply ON or OFF.

NOTE: 

• When the key is not turned to ON or OFF, either the “KEY_NO” or the “KEY_NC” signal 

is ON. These signals will not simultaneously turn OFF.

• These signal lines must be disconnected (NC) when the model without a key switch is 

used.

Signal name

Sop reset

Stop

EMG0

0 (OFF)

1 (ON)

EMG1

1 (ON)

0 (OFF)

EMG2

1 (ON)

0 (OFF)

Signal name Not pressed

Pressed to the 
intermediate position

Pressed to the 
innermost position

ENB0

0 (OFF)

1 (ON)

0 (OFF)

ENB1

0 (OFF)

1 (ON)

0 (OFF)

Signal name

Turn OFF this product

Turn ON this product

KEY_NO

0 (OFF)

1 (ON)

KEY_NC

1 (ON)

0 (OFF)

Содержание GP-4311HT






















Отзывы: