Prio Expert MO Series Скачать руководство пользователя страница 16

16

Water Storage Tank Service

Water storage tank may require air repres-
surizing if you notice low water delivery rate 
even with full tank.

The storage tank has the bladder inside 
which separates air from water. On the lower 
side of the tank there is the air valve con-
nected to the compressed air chamber. The 
top water inlet-outlet port (where the tank 
valve is mounted) is connected to the pure 
water chamber. When you open the faucet, 
the compressed air would compress the 
bladder to force the water out of the tank.

In an empty tank, air pressure in the air 
chamber should be 5-8 psi (0.35-0.55 bar). If 
pressure drops below this threshold you may 
notice low delivery rate of pure water from 
the tank.

To recharge the tank:

Shut off the water supply valve.

Drain the tank by opening the faucet to al-
low water to run until it stops.

Check to see if there is still water in the 
storage tank. If the tank feels heavy, 

that means you need to recharge the 
air chamber and continue the following 
steps. If the tank feels light, that means 
it is not time yet to recharge the tank at 
this moment.

Locate  the  air  valve.  Use  bicycle  tire  air 
pump to pump air into the tank through 
this valve. Keep the faucet open while 
pumping air so that all water inside the 
tank can be purged.

After all water has been drained from the 
tank, use an air pressure gauge to check 
the tank pressure. The tank should have 
5-8 psi (0.35-0.55 bar) of pressure when 
it’s empty. Add or purge air if necessary.

Open the water supply valve and close the 
faucet to allow refilling of the tank.

Please note that storage tank service life is 
limited. Take into consideration that it stores 
water of room temperature and is not ster-
ile, thus it may become the source of a sec-
ondary  contamination  over  time.  Unpleas-
ant smell or taste may appear in the water. 
If changing the post-filter doesn’t solve the 
problem your tank may require retirement 
and your system needs a new tank.

Prio, Prio logo are the trademarks of DWT Deutsche Wassertechnologien GmbH, Germany. 
As used herein, ® denotes registered trademark status in Germany only.

Copyright © DWT Deutsche W

assertechnologien GmbH, Germany, 2014, 2019

Содержание Expert MO Series

















Отзывы: