Printronix SV 2 Series Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 69

background image

254764-001 Rev B 23

High Density Focus: Analyze bar codes with 5 mil X dimension
Custom focus distances are available to achieve various spot sizes – contact PRINTRONIX Technical
support for details.

Power

•

+5 Volts DC, +/- .25 Volt

•

1 amp maximum

Sync

See the Sync Inputs Section for more details
I/O connector pin 4 input:

•

ttl switching level threshold

•

Maximum input voltage swing: +/- 12 VDC

•

100 K ohm internal pull-up resistor to 5 volts DC

I/O connector pins 1 (+), 2 (-) isolated input:

•

24 Volts DC nominal input for sensing

•

30 Volts DC maximum input, approximately 15 Volts minimum for sensing

•

This input is ground isolated from 5 VDC power

•

Sync input recovery time: 12.5 milliseconds minimum

Outputs

•

Open Drain FET (Field Effect Transistor) – no internal pull-up resistor

•

External Pull-up Voltage: 0 - 30 Volts DC

•

Sink current: 100 milliamps maximum

SYMBOLOGIES

•

USS Code 128

•

USS Code 39

•

USS Code 93

•

USS Codabar

•

USS Interleaved 2 of 5

•

UPC versions A and E (including 2 and 5 digit supplemental codes)

•

EAN-13 and EAN-8 (including 2 and 5 digit supplemental codes)

OPERATION MODES

The SV 2 Series is very flexible, with many programmable features, but basic system operation can be
broken down into three modes. Two modes include a sync signal and one mode operates without a sync
signal. These modes are programmable via SV Command Language and PRINTRONIX ScanVision
software.

Sync Mode – Moving Bar Codes

In this mode, a sync signal is used as an indicator to determine when an object or label containing a bar
code(s) has entered or exited the laser beam. Bar codes are analyzed and ports activated, transmissions sent,
etc. as the bar codes pass through the beam. The SV unit is programmed for the number of bar codes to
expect during a sync period (see Sync Input Section), therefore the SV unit can detect missing or
undetectable bar codes.

A hardware input is the most common sync source for this mode.

«
...
24
25
26
27
28
...
»

Содержание SV 2 Series






































































Отзывы:

Нет отзывов

Похожие инструкции для SV 2 Series

Бренд: Cameo Страницы: 56

Бренд: Kodak Страницы: 74

Бренд: SICK Страницы: 28

Бренд: Kodak Страницы: 121

Бренд: R&S Страницы: 17

Бренд: Shining 3D Страницы: 16

MobileOffice S410

Бренд: Plustek Страницы: 2

Бренд: kaarta Страницы: 95

Бренд: Faro Страницы: 340

DiMAGE DiMAGE Scan Multi PRO

Бренд: Minolta Страницы: 129

Бренд: Uniden Страницы: 39

SCANFRONT M11058

Бренд: Canon Страницы: 28

Бренд: NCR Страницы: 142

Бренд: Panasonic Страницы: 24

Бренд: Scanivalve Страницы: 96

Бренд: PCTEL Страницы: 23

Бренд: Inuvio Страницы: 14

Бренд: Eurotech Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды