Primus D55 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 82

Primus D55 Скачать руководство пользователя страница 45

70276001

43

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

54. CYLINDER SHEAVE

Refer to Figure 14.
a. Support drive guard cover and remove screws

holding guard to rear of tumbler. Refer to
Figure 11.

b. Loosen the four jackshaft assembly attaching

nuts. Refer to Figure 13.

c. Rotate the adjusting nuts counterclockwise

(approximately three turns).

d. Slide jackshaft assembly upwards to loosen the

cylinder belts.

e. Remove cylinder belts.

f. Remove bushing setscrew. Refer to Figure 14.

g. Remove screws from tapered bushing.
h. Remove tapered bushing by putting the screws

removed in step “g” into the threaded holes in
the bushing. Turning the screws inward will
force the bushing out of the cylinder sheave.

i. Remove cylinder sheave.

Figure 14

TMB1784S

Cylinder

Sheave

Cylinder

Belt

Drive

Belt

Bolt

Nut

Setscrew

Tapered

Bushing

Snap

Ring

Step

Pulley

Jackshaft

Assembly

«
...
43
44
45
46
47
...
»

Содержание D55



















































































Отзывы:

Нет отзывов