Primus D55 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 82

Primus D55 Скачать руководство пользователя страница 43

70276001

41

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

52. DRIVE BELT

Refer to Figure 14.
a. Support drive guard cover and remove screws

holding guard to rear of tumbler. Refer to
Figure 11.

b. Loosen the four jackshaft assembly attaching

nuts. Refer to Figure 13.

c. Rotate the adjusting nuts counterclockwise

(approximately three turns).

d. Slide jackshaft assembly upwards to loosen the

cylinder belts.

e. Remove cylinder belts.

f. Remove drive belt.

NOTE: After reinstalling drive belt, adjust cylinder
belts then drive belt.

53. STEP PULLEY ASSEMBLY

Refer to Figure 14.
a. Support drive guard cover and remove screws

holding guard to rear of tumbler. Refer to
Figure 11.

b. Remove cylinder belts and drive belts.
c. Remove snap ring and pull step pulley off of

jackshaft.

Refer to Table 1 on page 42 for critical torques.

NOTE: Belt tension from step pulley to cylinder
shaft pulley can be measured to ensure proper
installation in one of the following ways:

• Burroughs Belt Tension Gauge initial reading

70-80 pounds.

• Force to deflect belt .38 inch at midspan with

initial tensioning 6.5 pounds.

• Burroughs Belt Tension Gauge reading after run

55-65 pounds.

Figure 13

T316PE3B

Cabinet

High Limit

Thermostat

Jackshaft

Assembly

Jackshaft

Eye Bolt

Attaching

Bolts

Jackshaft

Eye Bolt

Adjusting

Nuts

Load Ready

Thermostat

«
...
41
42
43
44
45
...
»

Содержание D55



















































































Отзывы:

Нет отзывов