background image

Assembly Instructions Page 2

MAKE SURE ALL BOLTS ARE TIGHT BEFORE

PROCEEDING TO INSTALLATION  

W A R N I N G

1

2

3

4

5

6

Open ratchet handle

flat and insert end of

strap through opening

Pull Strap through

opening

Insert end of strap

through slot in ratchet

wheel

Ratchet handle back

and forth to tighten 

strap

To release tension, push 

spring loaded retaining lock

and simultaneously pull

on strap

After strap is tight,

close handle to 

the locked position

Detailed Ratchet Strap Instructions

Model: PVHA-100

Standz-Up Ladder Stand Aid

Distributed by Acheson Harriman Swan, LLC, 2407 W. Euclid Ave., Littleton, CO  80120

Customer Service Department 1-866-972-6168

www.primaltreestands.com

©2021 (rev. 1/21)

5

Fit the 

2-M8 Quickclips      

onto each Left and right

Ladder Support brockets          .

NOTE:

 These Quickclips

will be used to secure the base of the ladder stand into

place during hoisting procedures. 

ALWAYS

 store these

Quickclips here when not in use. 

NEVER

 use this

product without these clips.

5

E

J

F

J

E

F

J

6

Ratchet Strap

Bracket should

face away from

the tree.

Attach Top Stabilizer Bar      to the Middle Stabilizer Bar

      using 

1-M6 Quickclip      . NOTE:

 The Ratchet Strap

bracket should be on the outside of the stabilizer bar

away from the tree.

K

6

A

B

A

B

K

7

G

G

Attach Ratchet Strap      to the right and left side of the

ratchet strap bracket on the Top Stabilizer Bar. Thread

the Ratchet Strap webbing loops though the slots of the

ratchet strap bracket and feed the other ends of the

straps though the loop to secure.  
See “Ratchet Strap Instructions” (below) for correct

usage.

7

G

Содержание PVHA-100








Отзывы: