Pride Mobility Quantum 6000Z series Скачать руководство пользователя

Страница: 27 / 43

Quantum 6000Z

www.pridemobility.com

V . C O M F O R T A D J U S T M E N T S

Figure 21. Foot Platform Adjustment

FOOT
PLATFORM
BRACKET

QUICK
RELEASE
FASTENERS

Figure 22. Quick Release Fastener Operation

LEVER (OPEN)

BOLT

NUT

CAM

UNCLAMPED

CLAMPED

LEVER (FULLY
CLOSED)

To change the controller position:

1. Turn off the power to the controller.

2. Loosen the rear shroud fasteners and remove the

rear shroud.

3. Unplug the controller connector from the power base.

4. Remove any wire ties securing the controller har-

ness to the armrest.

5. Flip up the armrest so it is perpendicular to the floor.

6. Loosen the setscrew on the controller bracket. See

figure 19.

7. Slide the controller out of the armrest.

8. Loosen the setscrew in the other armrest.

9. Place the controller in the other armrest.

10. Tighten the setscrew in each armrest.

11. Route the controller harness to the back of the power

base and plug in the controller. See figures 12 and 13.

12. Replace the rear shroud and tighten the fasteners.

13. Secure the controller harness to the armrest with

wire ties. See figure 13.

NOTE: If your power chair is equipped with a Spe-

cialty Seat, Synergy Seat, or TRU-Balance 2 Power

Positioning System, loosen the mounting screws in the

mounting block, transfer the mounting block and con-

troller to the opposite armrest, and tighten the mount-

ing screws. See figure 20.

Foot Platform Height Adjustment

The foot platform height is easily adjusted to different

heights in 1.27-cm (0.5-in.) increments.

To raise or lower the foot platform:

1. Remove the quick release fasteners from the foot

platform bracket. See figure 21.

2. Raise or lower the foot platform to the desired height.

3. Reinstall the quick release fasteners into the foot

platform bracket and tighten.

Foot Platform Depth Adjustment

To adjust the foot platform depth:

1. Remove the quick release fasteners from the foot platform bracket. See figure 21.

2. Move the foot platform in or out to the desired depth.

3. Reinstall the quick release fasteners into the foot platform bracket and tighten.

Quick Release Fasteners:

The foot platform is attached to the power base with two quick release fasteners. See

figure 21. Each quick release fastener consists of a bolt, a lever, and a nut. See figure 22. The lever has a cam on

the end that allows it to clamp into place. The quick release fastener has two states: clamped and unclamped.

When the lever is open, the quick release fastener is unclamped. When the lever is closed, the quick release

fastener is clamped.

Содержание Quantum 6000Z series












































Результаты поиска

Содержание Quantum 6000Z series

Отзывы:

Похожие инструкции для Quantum 6000Z series

Бренды по названию

Популярные бренды

Pride Mobility Quantum 6000Z series, Руководство пользователя

Результаты поиска

Содержание Quantum 6000Z series

Отзывы:

Похожие инструкции для Quantum 6000Z series

Бренды по названию

Популярные бренды