background image

12

www.pridemobility.com

Quantum 6000Z

I I .   S A F E T Y

Public Streets and Roadways

WARNING! You should not operate your power chair on public streets and roadways. Be aware

that it may be difficult for traffic to see you when you are seated on your power chair. Obey all

local pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed with

extreme caution.

Outdoor Driving Surfaces

Your power chair is designed to provide optimum stability under normal driving conditions—dry, level surfaces

composed of concrete, blacktop, or tarmac. However, Pride recognises that there will be times when you will

encounter other surface types. For this reason, your power chair is designed to perform admirably on packed soil,

grass, and gravel. Feel free to use your power chair safely on lawns and in park areas.

Avoid driving on uneven terrain and/or soft surfaces.

Avoid tall grass that can entangle the running gear.

Avoid loosely packed gravel and sand.

If you feel unsure about a driving surface, avoid that surface.

Inclement Weather Precautions

Exposure of your power chair to inclement weather conditions should be avoided whenever possible. If suddenly

caught up in rain, snow, severe cold or heat while operating your power chair, proceed to shelter at the earliest

opportunity. Thoroughly dry your power chair before storing, charging, or operating your power chair.

PROHIBITED! Operating in rain, snow, salt, mist/spray conditions, and on icy/slippery surfaces

can have an adverse affect on the electrical system. Maintain and store your power chair in a

dry and clean condition.

WARNING! Prolonged exposure to hot or cold conditions may affect the temperature of

upholstered and non-upholstered items on the power chair, possibly resulting in skin irritation.

Exercise caution when using the power chair in extremely hot or cold conditions or when

exposing your power chair to direct sunlight for prolonged periods of time.

Stationary Obstacles (Steps, Kerbs, etc.)

Proceed with extreme caution when driving near raised surfaces, unprotected ledges and/or drop-offs (kerbs,

porches, stairs, etc.). Be sure your power chair is traveling perpendicular to any kerb you may be required to

navigate.

To navigate up over a kerb or stationary obstacle:

1. Approach the kerb or obstacle slowly, and make sure the power chair is traveling perpendicular to the obstacle.   
     See figure 2.
2.  Increase the forward speed just before the front wheels come in contact with the obstacle.
3.  Reduce the forward speed only after the rear wheels have cleared the obstacle.

To navigate down a kerb or stationary object:

1.  Approach the kerb or obstacle slowly, and make sure the power chair is traveling perpendicular to the obstacle. 
     See figure 2.
2.  Reduce the forward speed just before the front wheels come in contact with the obstacle.
3.  Increase the forward speed only after the rear wheels have cleared the obstacle and you are once again on a

level surface.

WARNING! Do not attempt to have your power chair climb or descend an obstacle that is higher

than 5 cm (2 in.) unless you have the assistance of an attendant.

WARNING! Do not attempt to have your power chair proceed rearward down any step, kerb, or

other obstacle. This may cause the power chair to tip.

Содержание Quantum 6000Z series












































Отзывы: