manualshive.com logo in svg

Price Industries Limited ECM Series, Руководство по устранению неисправностей

Поделиться
Скачать
Price Industries Limited ECM Series Скачать руководство пользователя страница 2

TABLE OF CONTENTS

ECM MOTOR

ECM Motor Background .................................................... 1

ECM Motor Power and Control Connectors .................. 2

ECM Motor Power Cable - 120 VAC ............................. 2

ECM Motor Power Cable - 240/277 VAC ...................... 3

NOTE:

 If a 120 VAC cable is used (with jumper) and 277 

VAC is applied to the motor it will be destroyed

ECM Motor Troubleshooting Checklist ............................... 3

ECM Speed Controller ....................................................... 4

Manual Mode ................................................................ 4

BAS Mode .................................................................... 5

Wiring and Cables ......................................................... 9

Typical Wiring Diagram ................................................ 14

Содержание ECM Series


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды