background image

Function:

The RCI-200-RF2 is a bi-directional data communication
system that exchanges the status of 2 dry contact inputs
and 2 analog inputs between a master and one or more
remote units. A basic system consists of one master
station and one remote station each with 2 dry contact
and 2 analog inputs and 2 'C' relay contact and analog
outputs. All signals are bi-directional so that data may be
read from the remote station and sent to it.

The license-free spread-spectrum radio technology
allows small systems to be set up with very little effort and
at low cost.

The technology ensures high

communication reliability even in RF-intensive
environments.

All units are sold without antennas. Pribusin carries a
complete assortment of antennas and accessories.

Options:

- A: 24VDC Power
- B: 240VAC Power
- N12: NEMA 12 Enclosure

Standard Features:

Bi-directional Communication using License-free
2.4GHz Radio Band

Spread-Spectrum Radio Technology Provides
Reliable Communication

2 Dry Contact and 2 Analog Inputs

2 'C' Relay Contacts and 2 Analog Outputs

Point-to-Point or Host-to-Multipoint Topologies

No Calibration Required

Microprocessor Controlled for High Accuracy

Power: 117 VAC 50/60 Hz (Optional 24 VDC)

High Noise Rejection

CSA and NRTL Approved (LR51078)

Re-Transmission & Error Correction Algorithms
ensure Accurate Data Transmission

Specifications:

Media: 2.4GHz Spread-Spectrum Radio
Range: up to 1500ft indoors with omnidirectional antenna

up to 12 miles line-of-sight with directional antenna

Protocol: MODBUS ASCII
Speed: 9600 BAUD
Radio Power Output: 1000mW max.
Operating Temperature: -4°F to +140°F (-20°C to +60°C)
Relay Contacts: 10A 1/8Hp @ 125VAC

6A 1/8Hp @ 277VAC

Power: 117 VAC, 60/50 Hz, 24VDC Available
Enclosure: NEMA4X (NEMA12 available as an option)

Model: RCI-200-RF2

Remote Control Signal Interface

With 2.4GHZ Radio Frequency Link

Page J10

Manufacturers of Process

Controls and Instrumentation

- R: Remote Radio

(Radio is in separate
enclosure and mounts
close to antenna to
prevent signal loss for
long cable runs)

Содержание Model: RCI-200-RF2















Отзывы: