Prevail-Catv WT-1550-EML Скачать руководство пользователя страница 6

Rev1.0

191107

6

8

Dimension

9

Naming Specification

1. RF1: One way RF input. RF2: two way RF inputs.
2. I

Standard model, no WDM.

II

Standard model + built-in WDM wavelength division multi built-in VOA electrical variable optical attenuator.

3. Output power mW

4. S

SC/APC. F

FC/APC

5. G male

Y female

6. 1P single power supply

2P dual power suppliers.

7. A220

AC220V

DC48

DC48V

8. The output is optional ITU standard wavelength, please specify the specific wavelength requirements in the order.
9. Please specify the WDM specification parameters in the order when selecting WDM.
10. Standard front panel is black engineering plastic material.
11. Standard optical interface and RF interface location are on the rear panel.
12. Standard Ethernet transponder.

10 Attention

Before unpacking, please confirm that the outer packaging is intact. If you think that the equipment has been damaged due to

transportation, etc., do not power on to avoid more serious damage to the equipment or accidental injury to the operator.

Before powering on the equipment, make sure that the grounding end of the chassis and power socket is reliably grounded.

The grounding resistance should be <4Ω, which can effectively protect against surge and static electricity.

The optical transmitter is a professional and technical equipment. The installation and debugging must be carried out by

professional technicians. Please read this manual carefully before operation to avoid damage to the equipment due to
misoperation or accidental injury to the operator.

When installing and debugging the optical device, there may be an invisible laser beam in the fiber connector. The fiber optic

connector should be avoided to be aimed at the human body, even not be directly viewed by the naked eye to avoid permanent
damage to body and eye!

When the fiber connector is not in use, it should be put on the dust jacket to avoid dust pollution and keep the

fiber end face clean.

Cordoba – Argentina -  www.unicorsa.com.ar

C

re

at

ed

 in

 M

as

te

r P

D

Ed

ito

r

Содержание WT-1550-EML







Отзывы: