Presys T-1200PIR, Техническое руководство

Страница: 23 / 25

PRESYS

Instruments T-1200PIR
Page 20
7.2 - Probe Calibration
The options of CAL>PROBE are:

ºC RESTORE
ºC : Adjust of the internal temperature sensor (internal Probe).
RESTORE : Restores the internal temperature sensor calibration parameters to
the factory values.
To readjust the internal Probe it is necessary to compare the value indicated by
the calibrator (Probe) and the temperature value from an external probe placed in an
insert. The temperature of the external probe should have high accuracy and should be
measured by a superthermometer (ST).
The option to adjust the internal sensor has seven points of adjustment. These
points are recorded via keys 1 to 7.
Before starting the calibration (adjustment), record in these points the respective
initial storing values, according to the table below.
Go to the manual operating mode (menu EXEC ) and generate all the seven
levels of temperature (set points from the table), writing down the value indicated by the
superthermometer (ST). Now, go back to the option Calibration/ Probe / ºC and record
the values indicated by the superthermometer.
Set point of the
temperature
generated (ºC)
Initial value
to record (ºC)
ST
indication
New value to
record
New
indication
of the ST
key
150 150.0 149.96 150.0 150.01 key 1
350 350.0 349.93 349.9 349.99 key 2
600 600.0 598.03 598.0 600.02 key 3
750 750.0 745.32 745.3 749.99 key 4
850 850.0 843.13 843.1 850.03 key 5
1000 1000.0 990.45 990.4 999.97 key 6
1100 1100.0 1087.11 1087.1 1100.05 key 7
8.0 - Maintenance
8.1 - Instructions for Hardware
There are no parts or components in the T-1200PIR temperature calibrators that
can be repaired by the user. Only the 10 A fuse, placed within the socket on the rear
can be replaced by the user.
The fuse may blow due to a voltage spike in the mains or a calibrator component
fault. Replace the fuse once. If a second fuse blows again, it is because the fault is not
that simple. Contact the Presys technical assistance or send the calibrator to the factory
for repair.
presys
: Adjust of the internal temperature sensor (internal Probe). : Adjust of the internal temperature sensor (internal Probe).
: Restores the internal temperature sensor calibration parameters to : Restores the internal temperature sensor calibration parameters to
To readjust the internal Probe it is necessary to compare the value indicated by To readjust the internal Probe it is necessary to compare the value indicated by
the calibrator (Probe) and the temperature value from an external probe placed in the calibrator (Probe) and the temperature value from an external probe placed in an an
insert. The temperature of the external probe should have high accuracy and should be insert. The temperature of the external probe should have high accuracy and should be
The option to adjust the internal sensor has seven points of adjustment. These The option to adjust the internal sensor has seven points of adjustment. These
Before starting the calibration (adjustment), record in these points the respective Before starting the calibration (adjustment), record in these points the respective
initial storing values, according to the table below. initial storing values, according to the table below.
Go to the manual operating mode (menu Go to the manual operating mode (menu EXEC EXEC ) and generate all the seven ) and generate all the seven
levels of temperature (set points from the table), writing down the value indicated by the levels of temperature (set points from the table), writing down the value indicated by the
superthermometer (ST). Now, go back to the option Calibration/ Probe / ºC and record
superthermometer (ST). Now, go back to the option Calibration/ Probe / ºC and record
the values indicated by the superthermometer.
the values indicated by the superthermometer.
Initial value Initial value
to record (ºC) to record (ºC)
ST ST
indication indication
New value to New value to
record record
presys presys presys presys presys presys presys
150.0 150.0 149.96 149.96
presys presys presys presys presys presys presys presys
350.0 350.0 349.93 349.93
presys presys presys presys presys presys presys presys presys presys
600.0 600.0 598.03 598.03
presys presys presys presys presys presys presys presys presys presys presys
750 750 750.0 750.0 745.32 745.32
presys presys presys presys presys presys presys presys presys presys
850 850 850.0 850.0 843.13 843.13
presys presys presys presys presys presys presys
1000 1000 1000.0 1000.0 990.45 990.45
presys presys presys presys presys presys presys
1100 1100 1100.0 1100.0 1087.11 1087.11
presys presys presys presys presys presys presys presys presys presys presys presys presys
8.0 - Maintenance 8.0 - Maintenance
8.1 - Instructions for Hardware 8.1 - Instructions for Hardware
There are no parts or components in the T-1200PIR temperature calibrators that There are no parts or components in the T-1200PIR temperature calibrators that
can be repaired by the user. Only the 10 A fuse, placed within the socket on the rear can be repaired by the user. Only the 10 A fuse, placed within the socket on the rear
presys
can be replaced by the user. can be replaced by the user.
The fuse may blow due to a voltage spike in the mains or a calibrator component The fuse may blow due to a voltage spike in the mains or a calibrator component
fault. Replace the fuse once. If a second fuse blows again, it is because the fault is not fault. Replace the fuse once. If a second fuse blows again, it is because the fault is not
that simple. Contact the Presys technical assistance or send the calibrator to the factory
that simple. Contact the Presys technical assistance or send the calibrator to the factory