background image

PRESTO OWNER’S MANUAL        

 Page 7

          DBP SERIES SCISSOR LIFTS

shock. Charger is equipped with an electric cord 

having an equipment-grounding conductor and 

grounding plug. The plug must be plugged into an 

outlet that is properly installed and grounded in ac-

cordance with all local codes and ordinances.

DANGER

Never alter the AC cord or plug provided. If it

will not fit outlet, have proper outlet installed by a 

qualified electrician. Improper connection can result 

in a risk of an electric shock.

D. BATTERY CHARGER CONNECTION

PRECAUTIONS

CAUTION

Connect and disconnect the DC output plug (or

clips) only when the AC cord is disconnected from 

the electric outlet. Never allow clips to touch each 

other.

1. To charge the unit, plug the charger into the 110 volt

wall outlet. The charger is pre-wired to the battery.

2. Disconnect the charger from the 110 volt wall out-

let

once the indicators read fully charged.

S E C T I O N  6

MAINTENANCE

Generally, the DBP Series DC Electric Scissor Lifts 

require very little maintenance.  Reasonable care will 

result in excellent trouble-free performance. 

WARNING!

Never go under or service lift with a load on the table 

or with the scissor mechanism unblocked. Always 

service the lift in a down position.

A.  

ROUTINE MAINTENANCE:

All routine maintenance should be performed monthly 

and can be performed on the standard DBP Series DC 

Electric Scissor Lifts in a lowered height position. Be-

fore performing any maintenance, disconnect the bat-

tery. Then raise the top over its center position, secure 

in place and perform the routine listed (1 through 7).

WARNING! 

Wood blocks should be cut to the proper length 

and be of a hard wood variety. Check for defects 

or damage to the blocks prior to each usage. These 

blocks are to be used only if the maintenance chock 

has been damaged or misplaced.

1). Check oil level. Add oil if necessary.

2). Check rollers for signs of wear. Replace if dam-

aged.

3). Check snap ring and shield. Replace if damaged.

4). Check hydraulic lines for damage or leaking. Replace 

if damaged.

5). Check for oil spots on the floor. Trace leaks to the 

proper fitting and tighten.

6). Check wiring for damage. Replace immediately if 

any sign of wear is evident.

7). Bearings on these lifts are permanently lubricated 

and require no servicing. Look for any signs of 

wear.

B. 

TROUBLESHOOTING MAINTENANCE:

LIFT WILL NOT MOVE

1. No operational noises:

a). Check power switch.

b). Check voltage at motor -- motor may have

failed.

2. Operational noises:

a). Lift may be overloaded or jammed. Check load

weight and obstructions.

b). Oil shortage -- reservoir low or oil line failure. 

Repair or replace.

3. Motor overheats:

a). Excessive cycle rate (15 per hour max.).

b). Low voltage -- check voltage at motor.

c). Oil starvation -- check filter in reservoir.

LIFT OPERATING SLOWLY

1. Up cycle:

a). Oil starvation -- check filter in reservoir.

b). Oil viscosity -- oil is too heavy or too thin.

c). Air in cylinder -- cycle lift with no load 2 times

and hold down button for 20 seconds after 

bottoming out on each cycle.

2. Down cycle: (single acting cylinders)

Содержание DBP Series





















Отзывы: