background image

128-9447

7 of 28

7

Start Inhibit Relay 

(When Used)

Remote Start Connection

Neutral Safety Switch

Closed In Park & Neutral

Neutral Start Switch will allow you to properly identify the circuit and select the correct installation 

method.   In addition you will realize  why  the connection of  the safety wire is required for all 

mechanical switch configurations.  

Failure to make this connection properly can result in personal injury and property damage.

In all installations it is the responsibility of the installing technician to test the remote start unit and  ensure 

that the vehicle cannot start via RF control in any gear selection other than park or neutral.

In both mechanical and electrical neutral start switch configurations, the connection of  the Yellow wire 

will be made to the low current start solenoid wire of the ignition switch harness.  This wire will have +12 

volts when the ignition switch is turned to the start (crank) position only.  This wire will have 0 volts in all 

other ignition switch positions.  

 NOTE:

  This wire must be connected to the vehicle side of the starter cut relay (when used).  For the 

electrical neutral switch configuration, this connection must be made between the starter inhibit relay, 

( when used ) and the neutral safety switch as shown in the following diagram. 

Failure to connect this wire to the ignition switch side of the of the neutral safety switch can result in per-

sonal injury and property damage. 

SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.

YELLOW START WIRE DETAIL

8 RED/BLACK Wire: 

+ 12 Volts Input

Note: The Red/Black and Pink are dry contacts and may be used for negative switching when necessary.  

Connecting the Red/Black to chassis ground will result in Pink being ground when the R/S is activated. 

This input is to be connected to a separate, (Other than the wire Red or Red/White is connected to), con-

stant on + 12 volt source which will  12 volt power to the additional ignition output, (Pink), wire.  

Connect this wire to a se 12 Volt source.

Содержание APS-687TWE





























Отзывы: