PRESONUS ACP88 Скачать руководство пользователя

Страница: 6 / 24

OVERVIEW

•

Separate Gate Sidechain/keying Jacks for Each Channel.

Your ACP-88 also includes a separate jack on each channel for

Gate

sidechain/Keying

. This is useful for

synching

an external sound to a snare track, for

example, or putting equalizers or filters

before

the

Gate key

to enable

Gating

only the

lower frequency of a kick drum, etc.

•

Balanced/Unbalanced Inputs and Outputs.

Your Acp-88 accepts either

balanced

unbalanced inputs

and

outputs

using

tip-ring-

sleeve

(

TRS

) connectors.

•

+ 4dBu or – 10dBV.

The internal operating level of your ACP-88 can be switched between

+4dBu

(pro levels)

–10dBV

(line levels), making it possible to use in virtually any application.

For Technical support please choose from the following options:

Phone: 800.750.0323
Email:

[email protected]

Website: www.presonus.com

*please visit the PreSonus forums at www.presonus.com/forums to find tips,
suggestions and general discussion for all PreSonus products.

Содержание ACP88
























Результаты поиска

Содержание ACP88

Отзывы:

Похожие инструкции для ACP88

Бренды по названию

Популярные бренды

PRESONUS ACP88, Руководство пользователя

Результаты поиска

Содержание ACP88

Отзывы:

Похожие инструкции для ACP88

Бренды по названию

Популярные бренды