background image

www.mounts.com  |  North America  800.368.9700  | Interna1-714-632-7100

Installation Guide

GB-AVSTOR3

7

Ceiling 

 Framework

24” T-Bar Frame

24” x 48” Ceiling Tile 

Opening 

The replacement 2’ x 2’ 

ceiling tile goes here. 

Figure 3

Figure 4

Figure 2

Figure 1

Quick Lock

6” Excess 1/16” 

Braided Cable 

1/16” Braided Cable To 

Ceiling Attachment 

Ceiling Framework

It is recommended that the following steps be performed by two people.

When adjusting the tension of the weight-bearing side of the Quick Lock, 

the 1/16” braided cable must be pulled through the Quick Lock until the 

desired tension is attained. 

Once the tension has been adjusted, be sure that there a minimum of 

6” of excess 1/16” braided cable on the non-weight bearing side of the 

Quick Lock (Figure 2). 

1)  Lift the ceiling box from the exposed ceiling framework until the 

     ceiling box’s outer lip rests against the bottom of the ceiling 

     framework (Figure 1).

2)  Adjust the 1/16” braided cable tension, but do not over tighten.

4)  Use cable cutters to remove any remaining 1/16” braided cable (optional).

If you installing the GB-AVSTOR3 through a 24” x 48” ceiling tile opening, 

attach a 24” T-bar frame ( commercially available) in the 24” x 48” ceiling tile 

frame for support and place a 2’ x 2’ ceiling tile adjacent to the GB-AVSTOR3 

(Figures 3 and 4).

3)  When you have the desired tension, pull the 1/16” braided cable through 

     the other side of the Quick Lock.

Page 6

Содержание GB-AVSTOR3










Отзывы: