Premier Hazard ShockWave 9005 Скачать руководство пользователя страница 11

11 

 

 

Fault LED

 – The siren amplifier has a fault LED incorporated into the front panel to aid debugging and 

troubleshooting of any detected faults. The LED will flash in different patterns to identify a particular 
fault as shown in the table below. The fault light should be treated as a warning of improper operation 
and possible causes should be investigated.  
 
 

Flash Pattern 

Detected Fault 

Steady on 

Short circuit on speaker detected 

Steady flashing (on, off) 

Over heated 

Two flashes with a pause 

Under voltage 

Three Flashers with a pause 

Over voltage 

Four flashes with a pause 

Over current, or short circuit 

 

 

Circuit protection

 – The siren amplifier has the following protective circuitry incorporated into it to 

ensure that fitting error don’t cause damage to the siren or vehicle systems as well as:  

 

 

Start delay

 – the siren will not work for several seconds after power is first applied to the 

siren amplifier, to allow voltage to stabilise after engine started, stopping damaging voltage 
transients effecting the speaker. 

 

Reverse Polarity protection

 – if the positive and ground lines have been reverse wired the 

siren will not function, however the siren amplifier and speaker will not be damaged by this. 

 

Over  temperature  protection

  –

 

In  the  event  of  the  siren  overheating  through  excessive 

prolonged use or extreme ambient temperatures. The siren will switch off the siren output 
until it has cooled sufficiently to resume operation. 

 

Over current protection

 – if the siren amplifier circuit is drawing too much current, caused 

by a speaker failing or short circuit, the siren will switch off the siren output. The power to 
the siren amplifier will have to be reset to clear this fault. 

 

Speaker  short  circuit  protection

  –  if  a  short  circuit  is  detected  on  the  speaker  the  siren 

output  will  switch off.  The  power  to  the  siren amplifier  will  have  to  be  reset  to  clear  this 
fault.

 

 

Over and under voltage protection

 – if the operating voltage is out of operating parameters 

for the voltage version of the siren, the siren will not operate. i.e. when 12V siren fitted to 
24V vehicle or if the vehicle battery is flat. 

 
 
 
 

 

D00217-00-A 

REL: 39983 

Содержание ShockWave 9005





















Отзывы: