background image

Page 27

For technical questions, please call 1-888-866-5797.

ITEM 62323 

        

SAFETY

SETU

p

Op

ERA

TION

M

AINTENANCE

Emissions Control System Warranty

United States Emissions Control 

Defects Warranty Statement

The United States Environmental Protection Agency (herein EPA) 

and Harbor Freight Tools (herein HFT) are pleased to explain the 

emissions control system warranty on your 2014-2015 Small Off-Road 

Engine (herein engine). Within the United States, new off-road, 

spark-ignition engines certified for model year 2014-2015, 

must meet similar standards set forth by the EPA.  HFT must 

warrant the emissions control system on your engine for the 

periods of time described below, provided there has been no 

abuse, neglect or improper maintenance of your engine.

Your emissions control system may include parts such as the 

carburetor or fuel-injection system, and the ignition system.  

Also included may be hoses, belts, connectors 

and other emissions-related assemblies.

Where a warrantable condition exists, HFT will repair your 

engine at no cost to you including diagnosis, parts and labor.

Manufacturer’s Warranty Coverage

The 2014-2015 engines are warranted for two (2) years.   

If any emissions-related part on your engine is defective, 

the part will be repaired or replaced by HFT.

Harbor Freight Tools Emissions Control 

Defects Warranty Coverage

Engines are warranted for a period of two (2) years relative 

to emissions control parts defects, subject to the provisions 

set forth below. If any emissions related part on your engine 

is defective, the part will be repaired or replaced by HFT.

 

Owner’s Warranty Responsibilities

•  As the engine owner, you are responsible for the performance 

of the required maintenance listed in your Owner’s Manual. 

HFT recommends that you retain all receipts covering 

maintenance on your engine, but HFT cannot deny warranty 

solely for the lack of receipts or for your failure to 

ensure the performance of all scheduled maintenance.

•  As the engine owner, you should, however, be aware 

that HFT may deny you warranty coverage if your 

engine or a part has failed due to abuse, neglect, 

improper maintenance, or unapproved modifications.

•  You are responsible for shipping your engine to a HFT 

warranty station as soon as a problem exists.  Contact the 

HFT Customer Service department at the number below to 

make shipping arrangements.  The warranty repairs should be 

completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights 

and responsibilities, you should contact the Harbor Freight Tools 

Customer Service Department at 1-888-866-5797.

Harbor Freight Tools Emissions Control Defects 

Warranty provisions

1.  Length of Coverage

HFT warrants to a first retail purchaser and each 

subsequent purchaser that the engine is free from 

defects in materials and workmanship that cause 

the failure of warranted parts for a period of two (2) years 

after the date of delivery to the first retail purchaser.

2.  No Charge Repair or Replacement

Repair or replacement of any warranted part will be 

performed at no charge to the owner if the work is 

performed through a warranty station authorized by HFT.  

For emissions warranty service, contact the HFT 

Customer Service Department at 1-888-866-5797.

3.  Consequential Damages Coverage

Coverage under this warranty shall also extend to the failure 

of any engine components caused by the failure of any 

warranted part while it is still covered under this warranty.

4.  Coverage Exclusions

Warranty claims shall be filed in accordance with the provisions 

of the HFT warranty policy explained in the box at the top of the 

previous page.  HFT shall not be liable for any loss of use of 

the engine, for any alternative usage, for any damage to goods, 

loss of time, or inconvenience.  Warranty coverage shall also be 

excluded for any part which fails, malfunctions, or is damaged 

due to failure to follow the maintenance and operating instructions 

set forth in the Owner’s Manual including, but not limited to:
a)  Use of parts which are not authorized by HFT
b)  Improper installation, adjustment or repair of 

the engine or of any warranted part unless 

performed by an authorized warranty center

c)  Failure to follow recommendations on fuel use 

contained in the Owner’s Manual

d)  Improper or inadequate maintenance of any warranted parts
e)  Repairs performed outside of 

the authorized warranty service dealers

f) 

Alterations by changing, adding to or 

removing parts from the engine.

5.  Service and Maintenance

Component parts which are not scheduled for replacement 

as required maintenance or are scheduled only for regular 

inspection to the effect of “repair or replace as necessary” 

are warranted for the warranty period. Any warranted part 

which is scheduled for replacement as required maintenance 

is warranted for the period of time up to the first scheduled 

replacement point for that part.  Any replacement part, provided 

it is equivalent in durability and performance, may be used 

in performance of maintenance or repairs.  The owner is 

responsible for commissioning a qualified technician/mechanic 

to perform all required maintenance, as outlined in the 

Inspection, Cleaning, and Maintenance section in this manual.

6.  Warranted parts

1)  Fuel Metering System

i) 

Carburetor and its internal parts.

ii)  Fuel pump (if so equipped).
iii)  Cold start enrichment system.

2)  Air Induction System

i) 

Intake pipe/manifold.

ii)  Air cleaner.

3)  Ignition System

i) 

Spark plug.

ii)  Magneto ignition system.

4)  Catalyst System (if so equipped)

i) 

Exhaust pipe stud.

ii)  Muffler.
iii)  Catalytic converter (if so equipped).

5)  Miscellaneous Items Used in Above Systems

i) 

Vacuum, temperature and time 

sensitive valves and switches.

ii)  Hoses, belts, connectors, and assemblies.

Содержание 62323





























Отзывы: