Precor Resolute RSL 313 Скачать руководство пользователя страница 11

Страница: 11 / 14

Tool: Torque wrench

Attach the cable to the weight stack. Thread the bolt into the top plate assem-

bly until the cable meets

ALL

of the following requirements.

The top weight begins to separate from the second weight.

The selector pin can be easily inserted into each of the weight plates.

The add-on weight is engaged when the latch is in the down posi-

tion.

At least six turns of the threads on the cable bolt extend into the

add-on weight selector stem.

The distance from the underside of the jam nut to the top of the washer

should be no more than

1.61 inch (41mm).

Tighten the locking bolt against the select stem to 50 ft-lb (81 N-m) of

torque.

1 weight labels

Remove back of labels. Align top holes and place pin into hole. Remove pin

and place into a lower hole on labels. Re-align labels as necessary and then

press firmly onto weights. Rub vigorously and thoroughly to adhere. Peel the

extra label away and rub remaining labels again.

Lubricate the guide rods with a Teflon-based lubricant, such as Tri-Flow Supe-

rior Lubricant. Remove any excess with a clean cloth or tissue.

41 mm

Содержание Resolute RSL 313















Результаты поиска

Содержание Resolute RSL 313

Отзывы:

Похожие инструкции для Resolute RSL 313

Бренды по названию

Популярные бренды

Precor Resolute RSL 313, Инструкция по сборке

Результаты поиска

Содержание Resolute RSL 313

Отзывы:

Похожие инструкции для Resolute RSL 313

Бренды по названию

Популярные бренды