Precor Resolute RSL 215 Скачать руководство пользователя

Страница: 12 / 14

Image

Hardware

Instructions

Snap the lower pulley shroud onto the lower front shroud . Place
the lower front shroud with pulley cover into frame.

1 M6 x 15 mm SHCS
Tool: Hex wrench, 4 mm

Secure lower pulley shroud.

Place the lower rear shroud onto the frame. Raise it enough to hook
over buttons.

Install the rear middle shroud . Slide it over the triangular tabs of the
lower shroud and hook it onto middle buttons.

Repeat for the front middle shrouds .

Install the upper rear and front shrouds . Ensure to hook them

over the buttons and spacers.

2 M10 x 40 mm SHCS
Tools: Hex wrench, 8 mm
Torque wrench

Place shroud crown on top and secure.

Recommended bolt torque

is 25 ft-lb (34 N-m).

Securely snap top tray into place.

Install the Shroud

IMPORTANT

Before installing the shroud, ensure that cable connections are correct and cables move smooth through their paths. If they do not,

STOP

and adjust cable and routing. In addition, ensure all fasteners (including those preinstalled) are tightened appropriately.

Note

The location of the lower pulley cover will vary depending on the model.

Содержание Resolute RSL 215















Результаты поиска

Содержание Resolute RSL 215

Отзывы:

Похожие инструкции для Resolute RSL 215

Бренды по названию

Популярные бренды

Precor Resolute RSL 215, Инструкция по сборке

Результаты поиска

Содержание Resolute RSL 215

Отзывы:

Похожие инструкции для Resolute RSL 215

Бренды по названию

Популярные бренды