background image

Cardio Theater Integrated Bracket Assembly Instructions

page 4

IMPOR

T

ANT SAFETY INSTRUCTIONS

1

Before You Begin

Thank you for adding the Precor Cardio Theater
Integrated LCD Screen Option to your EFX

®

. This

option will add a new dimension to your workout.

For proper installation, please read this guide
thoroughly and follow the assembly instructions.

Obtaining Service

For information about product operation or service,
refer to the Precor web site at www.precor.com. Should
you need more information regarding customer support
numbers or a list of Precor authorized service centers,
visit the Precor website at www.precor.com/contact.

Unpacking the Equipment

The Cardio Theater Integrated Bracket for the LCD
Screen is shipped in one box with the following
items:

Bracket assembly

Power extension cable

Four Phillips-head screws

Rubber adapter mounts

If any items are missing, contact the dealer
from whom you purchased the unit or call a
Precor Commercial Products Customer Support
Representative.

Important:

 To complete the assembly of the

Cardio Theater Integrated Bracket, you need the
Cardio Theater LCD Screen Option, which is shipped
in a separate box. Included with the screen are two
cables (coaxial/power cable and controller cable),
which you will need during the assembly process.

Important Safety Instructions

When using exercise equipment, basic
precautions should always be taken,
including the following:

Read all instructions before using
the unit.

 These instructions are

written to ensure your safety and to
protect the equipment.

Use the equipment only for its
intended purpose.

 Do not use

accessory attachments that are not
recommended by the manufacturer,
as such attachments might cause
injuries.

Always check the unit before each
use.

 Make sure that all fasteners and

cables are secure and in good
working condition.

Important

: The important safety

instructions written here reflect a portion
of what is found in the Precor EFX
owner’s manuals. Please review and
follow the safety instructions found there.

Before You Begin

Содержание HANDBOEK EFX 546i





























Отзывы: