Precor Bicycle-mounted Child Seat C842 Скачать руководство пользователя страница 70

Страница: 70 / 87

C842, C842i, C846, C846i Upright and Recumbent Cycle

Page 70

Procedure 7.15 - Replacing the Secondary Drive Belt

1. For C842, C842i, C846i and C846 version 2 units, skip to step 11. For C846 version 1 units,

continue with step 2.

2. Set the on/off switch in the off position.

3. Remove the left hand cover per Procedure 7.1.

4. Loosen the upper and lower alternator mounting bolts and rotate the alternator so that tens

5. rotate the secondary pulley and guide the secondary drive belt off of the secondary pulley.

Diagram 7.24 - Secondary Drive Belt Mounting, C846 version 1

6. Remove the secondary drive belt.

7. Set the replacement secondary drive around the alternator pulley and the upper half of the

secondary pulley. Slowly rotate the secondary pulley and guide the secondary drive belt

onto the secondary pulley.

8. Re-tension the secondary drive belt per Procedure 5.2.

9. Check the cycle’s operation per Section 4.

Secondary

Drive Belt

Upper Alternator

Mounting Bolt

Lower Alternator

Mounting Bolt

Содержание Bicycle-mounted Child Seat C842
























































































Результаты поиска

Содержание Bicycle-mounted Child Seat C842

Отзывы:

Бренды по названию

Популярные бренды

Precor Bicycle-mounted Child Seat C842, Руководство по обслуживанию

Результаты поиска

Содержание Bicycle-mounted Child Seat C842

Отзывы:

Бренды по названию

Популярные бренды