Precor 600 Series Скачать руководство пользователя страница 3

Страница: 3 / 16

Treadmill Assembly Guide

Follow the steps in the order listed in this assembly guide. For more product

information, visit us at

www.precor.com.

WARNING

At least two people are required to assemble the equipment. DO NOT

attempt assembly by yourself.

Assembly requirements

IMPORTANT

Before you fully tighten a fastener, check that its head is flush with the surface of

the equipment. If not, cross-threading may have occurred. DO NOT attempt to

rework the assembly as more damage to the equipment will occur. Instead,

contact Customer Service at www.precor.com.

We recommend you:

• Assemble the equipment close to where you plan to use it.
• Assemble the equipment on a solid, flat surface so that it remains level and

stable.

• Locate the equipment a minimum of 19.7 in. (0.5 m) on each side of the treadmill

and 78 in (2 m) behind the treadmill.

• DO NOT move the equipment without assistance.

Torque measurements

Use the following torque measurements to tighten the fasteners. If a torque is not

provided, then fully tighten the fastener with the appropriate tool.

• Socket head cap screw - 25 ft-lb (33.90 Nm)
• Button head screw - 25 ft-lb (33.90 Nm)

Right upright
support

Left upright
support

Base side
cover

Dash assembly

Hood

Arm cover

Bottom arm
cover

Heart rate
bar assembly

Safety key
assembly

Adjustable foot

Front arm
cover

Содержание 600 Series

















Результаты поиска

Содержание 600 Series

Отзывы:

Бренды по названию

Популярные бренды

Precor 600 Series, Инструкция по сборке

Результаты поиска

Содержание 600 Series

Отзывы:

Бренды по названию

Популярные бренды