background image

PD6720 Field-Mount Loop-Powered Rate/Totalizer 

Instruction Manual

 

 

PRECISION DIGITAL CORPORATION

 

 

233 South Street • Hopkinton MA 01748 USA 
Tel (800) 343-

1001 • Fax (508) 655-8990 

www.predig.com

 

 

 

 

 

 

  NEMA 4X, IP66 Loop-Powered Field-Mount Rate/Totalizer  

  4-20 mA Input with ±0.03% Accuracy 

  3.0 Volt Drop (6.0 Volt Drop with Backlight) 

  Easy Field Scaling in Engineering Units without Applying an Input 

  0.7" (17.8 mm) 5 Digits Upper Display for Rate 

  0.4" (10.2 mm) 7 Alphanumeric Characters Lower Display for Total, Tag, or Units 

  Simultaneous 5-Digit Rate and 7-Digit Total Display 

  Rate in Units per Second, Minute, Hour, or Day 

  Display Open Channel Flow with Programmable Exponent Feature 

  Open Collector Pulse or Alarm Output 

  Display Mountable at 0°, 90°, 180°, & 270°  

  SafeTouch

TM

 Through-Window Button Programming 

  HART

®

 Protocol Transparent 

  Loop or External DC-Powered Backlight Standard 

  Operating Temperature Range: -40 to 75°C (-40 to 167°F) 

  Conformal Coated PCBs for Dust and Humidity Protection 

  Password Protection for Programming Only 

  32-Point Linearization, Square Root Extraction and Programable Exponent Function 

  Wide Viewing Angle 

  Flanges for Wall or Pipe Mounting 

  Plastic NEMA 4X, IP66 Enclosure  

  Three 3/4" NPT Threaded Conduit Openings (Two Plugs Installed) 

  Stainless Steel Tag Available 

  2" U-Bolt Kits Available 

  3-Year Warranty

Содержание PD6720 Series


























Отзывы: