Precision Digital Corporation PD6622-L2N Скачать руководство пользователя страница 11

Страница: 11 / 45

Loop Leader PD6620 Series Loop-Powered Flow Rate/Totalizers

Instruction Manual

Installation

There is no need to remove the meter from its case

to complete the installation, wiring, and setup of the

meter for most applications.

PD6626 and PD6628 installation must be

performed in accordance with Control Drawing

LIM6600-2

in order to meet agency approval

ratings

Unpacking

Remove the meter from box. Inspect the packaging

and contents for damage. Report damages, if any,

to the carrier.
If any part is missing or the meter malfunctions,

please contact your supplier or the factory for

assistance.

Panel Mounting Instructions

•

Prepare a standard 1/8 DIN panel cutout – 3.622"

x 1.772" (92 mm x 45 mm). Refer to

Figure 1

and

Figure 2

below, for more details.

•

Clearance: allow at least 4.0" (102 mm) behind

the panel for wiring.

•

Panel thickness: 0.04" - 0.25" (1.0 mm - 6.4 mm).

Recommended minimum panel thickness to

maintain Type 4X rating: 0.06" (1.5 mm) steel

panel, 0.16" (4.1 mm) plastic panel.

•

Remove the two mounting brackets provided with

the meter (back-off the two screws so that there is

¼" (6.4 mm) or less through the bracket. Slide the

bracket toward the front of the case and remove).

•

Insert meter into the panel cutout.

•

Install mounting brackets and tighten the screws

against the panel. To achieve a proper seal,

tighten the mounting bracket screws evenly until

meter is snug to the panel along its short side.

DO NOT OVER TIGHTEN, as the rear of the

panel may be damaged.

Figure 1. 1/8 DIN Panel Cutout Dimensions

Figure 2. Panel Mounting Details

Содержание PD6622-L2N














































Результаты поиска

Содержание PD6622-L2N

Отзывы:

Похожие инструкции для PD6622-L2N

Бренды по названию

Популярные бренды

Precision Digital Corporation PD6622-L2N, Инструкция по эксплуатации

Результаты поиска

Содержание PD6622-L2N

Отзывы:

Похожие инструкции для PD6622-L2N

Бренды по названию

Популярные бренды