PRAXSYM PAMS Скачать руководство пользователя страница 9

Page 8 

P R A X S Y M    

 

Monitor mode is included to emulate the function of the TS-31A 

system.  The TS-31A is the predecessor to PAMS.  Monitor mode 
uses the 12 position RF switch included with the PAMS.  It also 

makes use of up to 12 Ground Plane Antennas which are sold 

separately.   

 
 
Initial Set-Up and Power On 



Attach one of the antennas to the BNC connector located on 

the top of the receiver. 



Power-On/Rotate POWER switch to ON position. 



The receiver will power on in Signal Strength mode.  To select 

a different mode, depress the MODE switch to rotate through 

Signal Strength, Spectrum Monitor, Shield Level, and Monitor 
modes. 



Allow the receiver to warm up for 5 minutes before taking 

measurement data.

 

 
Set Frequency  



The receiver always powers up tuned to 900 MHz. 



Rotate the FREQUENCY adjust knob to tune the receiver in   
1 MHz steps. 



Depress the F.DIGIT switch to toggle the step size between   

1 MHz and 100 kHz.  The current step size is displayed on the 

FR ADJ line of the display. 



The frequency can be set in either Signal Strength or Shield 

Level mode.  The receiver will remain tuned to this frequency 

as it is rotated through it’s modes of operation.  In Spectrum 
Monitor mode, this frequency will become the center 

frequency of the 12 MHz frequency span.  Using the THOLD 

arrow keys in Spectrum Monitor mode to move to a different 
part of the spectrum will not effect the receiver frequency 

when changing modes. 



The Spectrum Monitor screen displays 12 MHz of signals at a 

time from 864-936 MHz.  Along the bottom of the screen the 
start, center, and stop frequencies are displayed.  The 

FREQUENCY select knob is used to move the marker across 

the spectrum.  The marker’s frequency and the measured 
signal level at that frequency are displayed at the top of the 

display screen. The  THOLD arrows scroll through the 12 MHz 
spans of the receivers frequency range. 

Содержание PAMS





















Отзывы: