PRAXSYM PAMS Скачать руководство пользователя страница 8

  

Chapter 3 Operation 

3.1 Receiver 

Receiver Modes 

The receiver can be operated in one 

of four different modes.  
 

 

In Shield Level mode the receiver 
can be used to measure the amount 

of attenuation/shield level that is 

provided by an enclosure or other 
obstacles between the transmitter 

and receiver.  Before a shield level 

test is conducted, the receiver is 
initialized with the transmitter to 

read 0dB shield level. 

 

In Signal Strength mode the receiver can be 

used to measure the signal level of a 
continuous wave signal.  The receiver has a 

narrow (+/-7.5 kHz) IF bandwidth 

enabling it to measure  a test signal in 
the presence of interfering signals in 

the same band.  Although the 

receiver has no demodulation 
capabilities, it can be used to measure 

the signal level of narrow band 

modulated signals. 

 

In Spectrum Monitor mode the 

receiver can be used to view a 12 MHz 

span of the frequency spectrum.  This 
mode is ideal for locating a clear 

frequency that you can use for 

conducting a test or for identifying 
large interfering signals that could 

cause errors in measurements.  

 

Page 7 

 

Spectrum Monitor Mode

 

 

 

Shield Level Mode

 

Содержание PAMS





















Отзывы: