Pratica Forza Express Скачать руководство пользователя страница 68

Страница: 68 / 90

POWER COMPONENTS

Ventilation System

The Forza Express oven ventilation system uses two 3400 RPM cooling fans (dimensions: 7in/172mm
x 6in/150mm) that exhaust all of the hot air from electronic compartment.

Testing Cooling Fans

Warning: For safety purposes, manually discharge capacitors before troubleshooting cooling fans
due to proximity.

Unplug the unit and remove the rear panel.

Manually verify the cooling fan spins freely and not seized.

•

If cooling fan is seized/ not spinning, replace the cooling fan.

Disconnect the cooling fan cables from the connectors and check for continuity.

•

If the meter registers continuity, then the cooling fan is fine.

•

If the meter registers no continuity or open, replace the cooling fan.

Fans

Содержание Forza Express



























































































Результаты поиска

Содержание Forza Express

Отзывы:

Похожие инструкции для Forza Express

Бренды по названию

Популярные бренды

Pratica Forza Express, Руководство по обслуживанию

Результаты поиска

Содержание Forza Express

Отзывы:

Похожие инструкции для Forza Express

Бренды по названию

Популярные бренды