Manufactured by:
Motoppar da Amazônia Indústria e Comercio de Eletrônicos LTDA
Praça Linear, 100, Bloco 2 - Centro - Santa Rita do Sapucaí - MG - CEP 37540-000 - Brasil
CNPJ: 09.084.119/0002-45
www.ppa.com.br | +55 14 3407 1000
GENERAL TERMS AND CONDITIONS OF WARRANTY
MOTOPPAR, Industry and Commerce of Automatic Gate Operators Ltd., registered with the CNPJ
(National Registry of Legal Entities) under Number 52.605.821/0001-55, located at 3526 Dr. Labieno da
Costa Machado Avenue, Industrial District, Garça – SP – Brazil, Zip Code 17400-000, manufacturer of PPA
Products, hereby guarantees this product against design, manufacturing or assembly defects and/or
supportively as a result of material quality flaws that could make its intended use improper or inadequate,
within a legal period of ninety days from time of acquisition, provided that the installation instructions
described in the instruction manual are observed.
Due to the credibility and trust placed on PPA products, we will add 275 more days to the period mentioned
above, reaching a warranty period of one year, likewise counted from the time of acquisition proven by
consumer through proof of purchase (Customer Receipt).
In case of defect, within the warranty period, PPA responsibilities are restricted to the repair or substitution
of the product manufactured by the company, under the following conditions:
1. Repair and readjustment of equipment may only be carried out by PPA Technical Assistance, which is
qualified to open, remove, and substitute parts or components, as well as repair defects covered by this
warranty; thus, failure on observing this guideline and the verified use of any non-original parts will cause
the resignation of this warranty on the part of the user;
2. The warranty will not extend to accessories such as cables, screw kit, fixing brackets, power supplies etc.;
3. Expenses for packaging, transportation and product reinstallation will be sole responsibility of the
consumer;
4. The equipment must be sent directly to the Company responsible for the sale (manufacturer's
representative), through the address contained in the purchase invoice, properly packed, thus avoiding
loss of the warranty;
5. Within the additional period of 275 days, visits and transportation in places where authorized technical
assistance is not available will be charged. The cost of transportation of the product and/or technician will
be sole responsibility of the consumer and
6. The substitution or repair of the product does not prolong the warranty time.
This warranty will be terminated if the product:
1. Is damaged by natural agents, such as atmospheric discharges, floods, wildfires, landslides etc.;
2. Is installed in an improper electric power supply or if it is not according to any of the installation
instructions displayed on the manual;
3. Shows defects caused by droppings, collisions or any other physical accident;
4. Shows signs of product violation or attempted repair by unauthorized personnel;
5. Is not used for its intended purpose;
6. Is not used under normal conditions;
7. Is damaged by accessories or equipment connected to it.
Recommendation:
We recommend that both the installation and the maintenance of the operator to be performed by an
authorized PPA technical service. If the product fails or has an improper operation, seek an Authorized
Technical Service to fix it.
SENSITIVITY ADJUSTMENT
This sensor has five sensitivity levels configured through the tactile switch “SW1”. When
pressing the tactile switch for 1 second, we have the sensitivity level feedback on the
“LD1” led. Configure the sensor sensitivity levels as shown below:
- “SW1” tactile switch pressed 1x: sensitivity level 1, LED “LD1” flashes 1x.
- “SW1” tactile switch pressed 2x: sensitivity level 2, LED “LD1” flashes 2x.
- “SW1” tactile switch pressed 3x: sensitivity level 3, LED “LD1” flashes 3x.
- “SW1” tactile switch pressed 4x: sensitivity level 4, LED “LD1” flashes 4x.
- “SW1” tactile switch pressed 5x: sensitivity level 5, LED “LD1” flashes 5x.
OBS.:
LEVEL 1 INDICATES LOWER SENSITIVITY, AND LEVEL 5 INDICATES HIGHER DETEC-
TION SENSITIVITY.
SMART SLIM RF
SENSOR
USER’S MANUAL
P31565 - 09/2022
Rev. 0
ATTENTION!
Do not use this equipment
without first reading the
User’s Manual.
LINE
TECHNICAL FEATURES
- Double pyroelectric element.
- 12-m detection range x 110° aperture.
- 2-second activation time on detection.
- 433.92Mhz transmission frequency.
- 5 levels of sensitivity.
- RF protection; 25v1m up to 1Ghz.
- 60-second stabilization time.
- Supply voltage: 3V lithium battery.
- Stand-by consumption: 5uA @ 3Vdc.
- Transmission consumption: 12mA @ 3Vdc.
CR2450 battery.
SENSOR DIMENSIONS
Note:
All dimensions are in millimeters.
PRECAUTIONS
- Do not touch the pyroelectric element of the sensor.
- Avoid possible sources of false alarms in the sensor detection area (e.g. air conditioners,
direct sunlight on the sensor lens, open places where it can be windy).
- Avoid direct white light to the sensor.
- Fix the sensor on solid walls that do not suffer vibrations.
- Do not run the sensor cables along the electrical power supply wiring.
Avoid obstacles in the sensor detection area.
100
40
34
DETECTION RANGE
The figure below shows the sensor detection range above and from the side.
The maximum coverage angle is 110o, and the reach is 12 m when
installed at 90o and 2.4 m above the ground.
MAIN COMPONENTS OF THE BOARD
The figure below shows the sensor board with its components:
RECORDING THE SENSOR IN THE ALARM PANEL
- Enter in wireless sensor recording mode on the alarm panel.
- Hold down the “SW1” tactile switch and check if the “LD1” led is oscillating (the sensor
will remain transmitting while the tactile switch is pressed).
Wait for confirmation from the alarm panel, then release the tactile switch.
ATTENTION!
2.4 m is the maximum
recommended height to
install the sensor.
“LD1” SIGNALLING
LED
3V LITHIUM
BATTERY
* PYROELECTRIC SENSOR
ATTENTION!
- AVOID TOUCHING THE SENSOR WINDOW.
- USE ONLY ETHYL ALCOHOL AND COTTON
WHEN CLEANING IS NECESSARY.
- DO NOT TOUCH THE SENSOR WITHOUT
PROTECTIONS TO AVOID ELECTROSTATIC
DISCHARGES.
WITH RESISTOR: LED ON
WITHOUT RESISTOR: LED OFF
“SW1”
TACTILE SWITCH
