manualshive.com logo in svg

Powervar ACDEF1000-11, Руководство пользователя, Страница: 34 / 63

Поделиться
Скачать
Powervar ACDEF1000-11 Скачать руководство пользователя страница 34

  30 

 

 

Symptom

 

Possible cause

 

Remedy

 

Fault code is shown as 43 and the icon 

 appears on the LCD 

display. The alarm beeps continuously. 

The UPS shut down automati-
cally because of  an overload 
on  the output of the UPS.  

Remove excess loads from UPS 
output and restart it. 

Fault code is shown as 14 and the icon 

 appears  on the LCD  

display. The alarm beeps continuously. 

The UPS shut down automati-
cally because of a short circuit  
on the output of the UPS. 

Check the output wiring and  
connected devices for a short 
circuit. Remove the short cir-
cuit. 

Fault code is shown as 01, 02, 03, 04, 
11, 12, 13 and 41 on the LCD display 
and the alarm beeps continuously. 

A UPS internal fault has oc-
curred. There are two possible 
results: 
1. The load is still supplied, but 
directly from AC power via 
bypass. 
2. The load is no longer sup-
plied by power. 

Contact your dealer. 

Battery backup time is shorter than the 
specified value. 

Batteries are not fully charged. 

Charge the batteries for at least 
five hours and then check ca-
pacity. If the problem still per-
sists, consult your dealer. 

Batteries are defective. 

Contact your dealer to replace 
the battery. 

Fault code is shown as 05 on the LCD 
display. At the same time, the alarm is 
beeping continuously and the output of 
the UPS is cut off. 

A UPS internal fault has oc-
curred and the BUS is short 
circuited. 

Consult your dealer. If  power 
is supplied again to the UPS 
before the UPS is repaired then 
the DC/DC mosfet will be dam-
aged. 

Содержание ACDEF1000-11
































































Отзывы:

Нет отзывов