Powervar ACDEF1000-11 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 63

Powervar ACDEF1000-11 Скачать руководство пользователя страница 16

12

3. Installation

The UPS and external battery cabinet are designed to be rack-mounted in four post frames or to be floor standing
in a tower configuration.

3.1 Tower Installation

ATTENTION:

Use all supplied mounting hardware on each UPS and extended battery cabinet.

          A. To install standalone, refer to the figure directly below :
               Assemble two feet as one tower stand.
               Align the two stands.
               Put the UPS module in the stands.






          B. To install a UPS module and one extended battery cabinet, refer to the figure directly below :
               Assemble two feet each with an extension as one tower stand.
               Align the two stands.
               Put the UPS module and external battery cabinet in the stands.

NOTE:

When installing the UPS or external battery cabinet with feet, please keep both feet a distance of 2.75in

(70mm) from the edge of the unit. See figure below :

«
...
14
15
16
17
18
...
»

Содержание ACDEF1000-11
































































Отзывы:

Нет отзывов