background image

5

ASSEMBLY

Do not permit fingers to touch the terminals of plug when 
installing or removing from outlet.
•  Inspect tool cords periodically, and if damaged, have
  repaired by an authorized service facility.
•  The conductor with insulation having an outer surface 
   that is green with or without yellow stripes is the 
   equipment-grounding conductor. If repair or replacement 
   of the electric cord or plug is necessary, do not connect 
   the green (or green and yellow) wire to a live terminal. 

A temporary 3-prong to 2-prong grounding adapter (see
Figure 9) may be used to connect this plug to a matching 
2-conductor receptacle as shown in figure 9. The 
temporary adapter should be used only until a properly 
grounded outlet can be installed by a qualified electrician. 

In Canada, the use of temporary adapter is not permitted 
by the Canadian Electric Code.  Where permitted, the rigid 
green tab or terminal on the side of the adapter must be 
securely connected to a permanent electrical ground such 
as a properly grounded water pipe, a properly grounded 
outlet box or a properly grounded wire system.
•  Many cover plate screws, water pipes and outlet boxes  
  are not properly grounded. To ensure proper ground,    
  grounding means must be tested by a qualified 
  electrician.

EXTENSION CORDS

Use proper extension cords. Make sure the extension 
cord is in good condition. Use only 3-wire extension cords 
have 3-prong grounding type plugs and 3-pole 
receptacles which accept the tool plug. When using an 
extension cord, make sure to use one heavy enough to 
carry the current of the machine. An undersized cord will 
cause a drop in the voltage, resulting in loss of power and 
overheating. Use the table to determine the minimum wire 
size (A.W.G.) extension cord. 

Extension Cord Length

Wire Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.W.G.
Up to 25 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
25 to 50 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16

NOTE:

 Using extension cords over 50 ft. long is not

recommended.

Figure 9  2-Prong Receptacle

Grounding
Means

Grounded outlet Box

Adapter

     WARNING

Содержание DP801

















Отзывы: